 |
(800) 894-0412 (208) 368-0415 (Fax)
info@clrwtr.com |
Banner SI-LS42 Series Locking Style Machine Safety Switch |
Banner SI-LS42 Series Locking Style Machine Safety Switches
- Switches lock a mechanical guard until hazardous motion stops completely.
- Two housing styles are available, based on voltage.
- Two locking mechanisms are available-spring lock with energized solenoid release and energized solenoid lock with
spring release.
- A wide range of solenoid voltages are available.
- Rotating head requires little or no tools to adjust to one of four positions.
- Rigid and flexible in-line actuators are available.
- Design meets positive opening requirements for safety interlocks.
|
|
If you are looking for Banner Safety Interlock Switch, please call us on
(800) 894 - 0412 or email us at
info@clrwtr.com
we will do our best to help you find the Machine Safety Switches that you are looking for at the most competitive prices possible.
If you are searching for Magnetic Style Switch technical information (data-sheets) please use the datasheets or product selection
guide page links.
|
Banner SI-MAG Series Magnet Style Switch |
Banner SI-MAG Series Magnetic Style Machine Switches
- Non-Contact safety switches are the best choice for washdown applications; the switch components are sealed and
rated NEMA 4X, IEC IP67
- Tolerant of dirt buildup, sensing distance, and alignment
- System consists of three components:
- Coded magnet
- Reed switch sensor
- Controller module
- Magnet contains several differently-polarized magnets, and sensor contains pole-stable reed contacts to minimize
any possibility of defeat
- Easy installation; can be concealed for added defeat resistance
- Sensor reed switches provide diverse input to the controller module
|
Banner SI-QM100 Series Locking Style Machine Safety Switch |
Banner SI-QM100 Series Locking Style Machine Safety Switches
- Positive opening safety contacts (IEC 60947-5-1) (not dependent upon springs)
- Protective Earth Terminal (IEC 60947-1)
- Keyed actuators discourage intentional tampering or defeat
- Choice of two locking mechanism types:
- Spring lock with energized solenoid unlock
- Energized solenoid lock with spring unlock
- Both types are available with choice of 24V dc or 120V ac solenoid operating voltage
- Actuator head rotatable in 90° increments
- Monitor contacts for both switching contact and solenoid status
- Standard mounting hole pattern (EN 50041)
|
Banner SI-QS75 & SI-QS90 Series Flat Pack Style Machine Safety Switch |
Banner SI-QS75 & SI-QS90 Series 75 mm & 90 mm Flat Pack Style Machine Safety Switches
- Mechanically coded actuators use two independent operating elements to minimize intentional tampering or defeat.
- Both housing styles are available in two sizes offering different contact configurations.
- Rotating head and top or side engagement allows for eight different actuator positions.
- Four standard actuators are available, as well as an optional high-extraction-force actuator.
- Design meets positive opening requirements for safety interlocks.
- IEC IP65 switch housing rating increases to IEC IP67 with addition of a screw to the wiring chamber door.
|
Banner SI-LS83 & SI-LS100 Series Limit Switch Machine Safety Switch |
Banner SI-LS83 & SI-LS100 Series Limit Switch Style 83 mm & 100 mm Machine Safety Switches
- Positive opening safety contacts (IEC 60947-5-1) (not dependent upon springs)
- Limit switch design (EN 50047)
- Mechanically-coded actuators utilize two independent operating elements to minimize intentional tampering or defeat
- Rotating head allows actuator engagement from four sides or four top positions; no tools are required to rotate head
- Low-profile design for limited space requirements; only 30.5 mm (1.3") depth
- Tough, glass-reinforced thermoplastic housing; metal actuator
- Choice of two in-line actuators or a flexible actuator
- Insulated device (IEC 60947-5-1)
|
Banner SI-HG63 Hinge Wing Safety Interlock Switch |
Banner SI-HG63 Hinge Wing Safety Interlock Switches
- Safety switch is integrated into a highly robust PBT housing and screwed onto the fine-cast stainless steel hinge.
- Safety switching point is repositionable.
- Right-hinge, left-hinge, and right-angle hinge models available; switches can also be converted to operate from the
opposite side.
- A non-switching blank hinge is also available (see page 7).
- Switch components are protected from mechanical impact, for superior performance to actuator-activated safety
switches; rated IEC IP67.
- Hinge operates to a full 270° range of motion; safety switching point (guard-closed position) is adjustable over the
full 0-270°operating range.
- Hinge can support an axial and radial load of 1200 N (120 Kg).
- When properly interfaced or used with an appropriate controller, two SI-HG63 switches on an individual gate or guard
can achieve safety category 4, per ISO 13849-1 (EN 954-1).
|
Banner SI-HG80 Series Hinge Wing Safety Interlock Switch |
Banner SI-HG80 Series Hinge Wing Safety Interlock Switches
- Safety switch is integrated and encapsulated into a load-bearing hinge, providing a high degree of protection from
intentional defeat
- Identical in appearance to non-switching blank hinge (see page 7)
- Switch components concealed inside the hinge are protected from mechanical impact, providing superior performance to
actuator-activated safety switches; rated IEC IP67
- Hinge operates to a full 180° range of motion; safety switching point (guard-closed position) is adjustable over the
full 0-180°operating range
- Hinge can support an axial load of 750 N and more than 1,000 N in radial direction
- When properly interfaced or used with an appropriate controller, two SI-HG80D switches can achieve safety category 4,
per ISO 13849 (EN 954-1)
- Robust zinc die-cast housing is corrosion resistant.
|
Banner SI-LS31H Series Limit-Switch-Style Machine Safety Switch |
Banner SI-LS31H Series 31 mm Limit-Switch-Style Machine Safety Switches
- Limit switch design (EN 50047)
- For use on doors or flaps
- Positive opening safety contacts (IEC 60947-5-1) (not dependent upon springs)
- Glass-reinforced thermoplastic switch housing with plated steel actuator
- Insulated device (IEC 60947-5-1) on all models with plastic housings
- Actuator head rotatable in 90 degree increments
|
Banner SI-LS31R Series Limit-Switch-Style Machine Safety Switch |
Banner SI-LS31R Series 31 mm Limit-Switch-Style Machine Safety Switches
- Limit switch design (EN 50047)
- Rotating shaft connects directly to door hinge
- Positive opening safety contacts (IEC 60947-5-1) (not dependent upon springs)
- Glass-reinforced thermoplastic switch housing with plated steel actuator
- Insulated device (IEC 60947-5-1) on all models with plastic housings
- Actuator head is rotatable in 90 degree increments
|
Banner SI-LM40 Series Limit Switch Style Machine Safety Switch |
Banner SI-LM40 Series Limit Switch Style Machine Safety Switches
- Mechanically coded actuators use two independent operating elements to minimize intentional tampering or defeat.
- Compact metal style switches are designed for limited space requirements in rugged environments
- SI-LM40MKH models are available with rigid and flexible in-line actuators.
- SI-LM40MKV models have a trumpet-style actuator.
- Rotating head requires little or no tools to adjust to four positions.
- Design meets positive opening requirements for safety interlocks.
|
Banner PICO-GUARD Fiber Optic Safety Interlock Switches |
Banner PICO-GUARD Fiber Optic Safety Systems
- Uses compact, non-contact fiber optic technology for personnel safety and equipment protection
- Eliminates electrical wires and expensive electrical wiring, for easy installation
- Offers choice of 2, 3 or 4 beam Grids and single-beam Points for perimeter and access guarding
- Features a variety of interlock switches for doors, guards, gates and covers
- Offers optical E-stop buttons for complementary protective measures to safeguarding devices that detect or prevent
inadvertent access to a hazard
- Includes four optical channels in each controller
- Available in controller models with optical channel auxiliary outputs and muting
- Includes two Universal Safety Stop Interface (USSI) inputs for direct connection of multiple safety devices
|
|
Our Banner Engineering distributors warehouse in Boise, Idaho stocks some Banner Safety Interlock Switches
enabling us to further assist you in finding the correct Banner Locking Style Machine Safety Switch for your application in
the Pacific Northwest USA. We can proudly say that we carry more Banner Engineering Limit Switch Style Mechanical Guard Opens
in stock than any other Banner Engineering distributors in the Pacific Northwest region. Whether we have Hinge Wing Safety
Interlock Switch in stock in Boise, Idaho or need to get them from Banner Engineering; Clearwater Tech can get Banner Flat
Pack Style Switches to you fast and save money!
It will be very helpful if you have the Banner Interlock Safety Switch part numbers ready, then
our sales representatives can provide you with a pricing and availability quote for Locking Style Machine Safety Switch that
you are looking for in seconds. If you do not have the part numbers for Banner Limit Switch Style Mechanical Guards, our
application engineers will be able to help you figure out the part numbers and get the price quote to you as soon as
possible.
Please be aware that we cannot sell Banner Sensors out of our Area of Primary
Responsibility (APR).
|
