Clearwater Tech Logo
Loading
Home | Contact Us
(800) 894-0412

Banner Engineering

Home   >   Products   >   Banner   >   Sensor Interface Modules

Banner Engineering

(800) 894-0412       (888) 723-4773 (Fax)
info@clrwtr.com

PS24-1 & PS115-1 Series

This interface module combines the functions of a power supply, a TEACH button, and an SPDT relay to economically interface dc-operated sensors for ac applications. The interface accepts either a 24V ac or 115V ac power supply, depending on model. It uses a transformer to isolate the input power supply from the dc sensor. The transformer output voltage is rectified and filtered to supply up to 100 milliamps to run dc sensors.

An integral TEACH push button can be used to activate the TEACH functions of a Banner Expert sensor. Remote TEACH capability also is available on all models (refer to hookups and sensor literature).

The SPDT relay is controlled via the relay coil input. A dc sensor output (either sinking or sourcing, depending on interface module model) can be tied to the relay coil input. The module Yellow LED is ON when the sensor output is active. The module Green LED is used as a Power indicator.

Banner PS24-1 & PS115-1 AC Power Supply Interfaces for Use with DC-Operated Sensors Distributors
PS24-1 & PS115-1 Series

If you are looking for Banner Sensor Interface Modules, please call us on (800) 894 - 0412 or email us at info@clrwtr.com we will do our best to help you find the Banner AC Power Supply Interfaces that you are looking for at the most competitive prices possible. If you are searching for Banner SIM-525T Power Supply technical information (data-sheets) please use the datasheets or product selection guide page links.

Model SIM-525T

The SIM-525T is a passive DIN-rail-mountable module that allows additional status indicators to be located in the user's control cabinet. It also provides a Remote TEACH push button for interfacing to any Banner 5-wire Expert product.

It is designed to provide remote indication and Teach capability for Banner M-GAGE & T-GAGE sensors, when their mounting does not allow easy access to the sensor (as when mounted underground or sealed in pavement, for example).

The module also features two separate "tie points" to allow for a sensor signal capture when using the Banner DPB1 Programming Box and sensor-specific monitor software. The tie points also can be used as a Teach input by the user's PLC.

Banner Model SIM-525T Power Supply for Use with 12-30V DC Sensor Distributor
SIM-525T Power Supply
  • Simple DIN-rail mount
  • Indicators for Power ON and Output Active
  • Includes sensor TEACH push button
  • Additional terminals provide in-situ data collection for some sensors

Models PPSIM

The PPSIM** series sensor interface module is a passive DIN-rail-mount or wall-mount module.

It enables remote external trigger and TEACH capability and provides remote indication of sensor status for Banner PresencePLUS P4 Sensors.

For mounting to a flat surface, unscrew one end cap, slide the DIN clips off of the housing, and replace the end cap. Use the screw-holes in the end caps for mounting to a flat surface.

P4 Sensor output must be set to NPN mode when used with an NPN interface module. P4 Sensor output must be set to PNP mode when used with a PNP interface module. See the System Setup window in the PresencePLUS GUI for output selections.

Banner Models PPSIM DC-Powered Interface Modules for PresencePLUS P4 Sensors Distributors
Models PPSIM
  • Low-cost interface between user's hardware and PresencePLUS P4 sensors
  • Available with two methods for connecting to sensor, depending on model:
    • 13-pin terminal strip for cordset with flying leads
    • DB-15 connector for model P4C..SIM cordsets (see Cables on page 4)
  • Available in current sinking (NPN) or current sourcing (PNP) output models
  • LED indicators for sensor status and active outputs
  • Integral External Trigger and Remote TEACH push buttons
  • Easy-to-adjust 45° screw terminals for electrical wiring
  • Built-in RS-232 serial port connector (DB-9, Female)
  • Simple DIN-rail-mount or wall-mount configuration

Our industrial factory automation supplies distributors warehouse in Boise, Idaho stocks some Banner Engineering products enabling us to further assist you in finding the correct sensor interface modules for your application in the Pacific Northwest USA. We can proudly say that we carry more Models PS24-1 & PS115-1 in stock than any other Banner Engineering distributors in the Pacific Northwest region. Whether we have Models PPSIM in stock in Boise, Idaho or need to get them from Banner Engineering; Clearwater Tech can get sensor interface modules to you fast and save money!

It will be very helpful if you have the Banner Models PS115-1 & PS24-1 part numbers ready, then our sales representatives can provide you with a pricing and availability quote for Model SIM-525T that you are looking for in seconds. If you do not have the part numbers for Banner AC Power Supply Interfaces, our application engineers will be able to help you figure out the part numbers and get the price quote to you as soon as possible.

Stock Check
Part No:
OR
Manufacturer:

Search Tips

Can't find a part number?
E-mail Us.

CONTRINEX Sensors

CONTRINEX ultrasonic sensors are cylindrical in form and delivered ready-to-connect with an integral 4- or 5-pole S12 connector. In addition to switching outputs, high resolution analog output (current or voltage) and dual-output (analog+digital or digital+digital) sensors are also available. Devices are offered in three technology versions: Diffuse, Reflex and Diffuse & With diffuse sensors, the target itself reflects the ultrasonic impulses.

NK Technologies Switches

AS0 Series low-current current sensing switches are specialized current sensing switches that combine an ultra-sensitive current transformer and signal conditioning electronics into a single package for sensing AC current from 3-350 mA. Useful for signal or lamp status monitoring, detecting low level fault currents or fan status proofing, the AS0 series features solid-state outputs and jumper-selectable ranges,