CTi Automation Logo
Loading
Home | Contact Us | Sitemap
(800) 894-0412

GE Sentrol Industrial

Home   >   Products   >   Edwards Signaling/UTC Fire & Security

GE Security - Sentrol Industrial

(800) 894-0412       (888) 723-4773 (Fax)
info@clrwtr.com

Position Sensors

Designed to make installation easier, these position sensors have earned their reputation for quality. They are built for durability and dependability. Most are conservatively rated at 100,000 cycles under full load, and 10,000,000 cycles under dry circuit.

Every reed connection is hand soldered and the reeds in all models are environmentally sealed. Like the GuardSwitch™ safety interlock switches, our position sensors are tested before they leave the factory - 100% of the time.

Our world-class manufacturing standards and attention to detail virtually eliminate all out-of-box failures. You can install the position sensors quickly and with every confidence in their reliability.

GE Security Sentrol Industrial 1032 Series Position Sensors Distributors

Magnetic Contacts

If you are looking for GE Sentrol Machine Safeguarding Products, please call us on (800) 894 - 0412 or email us at info@clrwtr.com we will do our best to help you find the GE Interlogix Interlock Switches that you are looking for at the most competitive prices possible. If you are searching for Sentrol Industrial Magnets technical information (data-sheets) please use the datasheets or product selection guide page links.

Guardswitches

The FailSafe Guardswitch is designed as a safety interlock to be attached to a machine's guard or door. Unlike a standard reed switch interlock, the circuit had been designed to have an "open" failure mode. If the main reed sticks closed when the guard opens, the in-line fuse will blow, opening the circuit. If the watchdog reed sticks closed when the guard closes, the in-line fuse will blow, opening the circuit. The circuit will draw up to 4.0A to blow the fuse in less than 200ms.

All GuardSwitches are non-contact, magnetic devices consisting of a switch and a magnet actuator. They are extremely tolerant of misalignment and the build-up of dirt, grease and other contaminants and are hermetically sealed. They actuate through wood, aluminum, stainless steel or any other nonferrous material. Allowing the interlock switches to be concealed in the machine for added protection against tampering.

Sentrol Non-Contact Magnetic GuardSwitches Distributor

FailSafe Guardswitch

"Integrity Series" Safety Relays

INT-22.5R1-24 Series GuardSwitch safety monitor relay is a two-channel safety switching device with self monitoring on each ON-OFF cycle.

INT-03 Series is a safety relay which uses positive-guided relays, configured for self-checking, to inhibit machine start-up in the event of an internal component failure.

The INT-04 relay can monitor contacts on external relays for controlling expansion block relays (INT-05 and INT-06).

The INT-05-024 or INT-05-120 Expansion Safety Relay is intended for use as part of a safety circuit. It provides three additional safe output contacts when used with the INT-03 Safety Monitoring Relay or INT-04 Emergency-Stop Safety Relay.

GE Security Sentrol Industrial INT-03 Series Safety Relays Distributors
"Integrity Series" Relays

Mechanical Safety Switches

Safety switches are used to detect the opening of machine guard doors, gates or panels and to prevent physical access to dangerous areas of the machine. Safety switches are designed to help deter tampering with either the internal machine controls or guards while in an unsafe condition.

All mechanical safety switches are equipped with positive opening contacts that open any normally closed contacts to assure machine shutdown when an unsafe condition is detected. Safety switches are furnished completely assembled, ready to mount to the machine.

Sentrol FR 996 Series Hinge-Operated Safety Switches Distributor
Mechanical Safety Switches

Our industrial factory automation supplies distributors warehouse in Boise, Idaho stocks some Sentrol Industrial products enabling us to further assist you in finding the correct GE Security Safety Relays for your application in the USA, Canada and Mexico. Whether we have GE Interlogix Position Sensors in stock in Boise, Idaho or need to ship direct from UTC Fire & Security to any USA cities; Clearwater Tech can get Sentrol Space Detection Sensors to you fast and save money! It will be very helpful if you have the Sentrol Glassbreak Detection Sensors part numbers ready, then our sales representatives can provide you with a pricing and availability quote for Edwards Signaling Safety Switches that you are looking for in seconds. If you do not have the part numbers for GE Sentrol Position Sensors, our application engineers will be able to help you figure out the part numbers and get the price quote to you as soon as possible.

Stock Check
Part No:
OR
Manufacturer:

Search Tips

Can't find a part number?
E-mail Us.

IDEC Interlocks

HS7A-DMP Non-Contact magnetic safety interlock switches perform the same functions as standard mechanical safety interlock switches, but are designed to be used in applications where non contact is desired between the switch and its actuating key. It's also being used where space is at a premium. The slim profile makes it easy to mount in locations out of the way of personnel and machine operation, reducing the possibility of damage or misalignment.

Banner Switches

The Purpose of an Emergency Stop Safety Module (E-Stop Safety Module) is to increase the control reliability of an emergency stop circuit. A 2-channel E-stop switch has two electrically isolated contacts.Both contacts of a 2-channel E-stop switch are monitored by the Safety Module. If either input is short-circuited, the Safety Module cannot be reset, and the controlled machinery cannot be restarted, following actuation of the E-stop switch.