(800) 894-0412       (208) 368-0415 (Fax)
info@clrwtr.com

Application

• Designed for general purpose indoor commercial use as a junction, pull or Switch box.

Standards

• UL-50 Type 1 & CSA Type 1
• Complies with: NEMA Type 1 & IEC 529, IP30

Construction

• Formed and spot welded from 16 or 14 gauge steel depending on size.
• Flat steel covers fastened with plated steel screws.
• Keyhole slots permit cover to be lifted off without removing screws entirely.
• Easily removed knockouts on all 4 sides (see drawings for sizes and locations).
• Through holes in back for wall mounting.
• Grounding location embossed in body.

If you are looking for Hammond Commercial Enclosures, please call us on (800) 894 - 0412 or email us at info@clrwtr.com we will do our best to help you find the Hammond Manufacturing Commercial Enclosures that you are looking for at the lowest prices possible. If you are searching for Hammond Commercial Enclosure technical information (data-sheets) please use the Hammond Data Sheets OR Product Selection Guide page links.

Application

• The splitter boxes are designed for indoor distribution of up to 600 V (max) service using either 3 or 4 wires.

Standards

• CSA Certified

Construction

• Formed and spot welded from 14 or 16 gauge steel.
• Factory installed Splitter Blocks.
• Series of knockouts on each side
• Padlocking hasp.
• Enclosure and cover are finished in ANSI/ASA 61 gray powder coating.

Application

• Designed for indoor housing of metering Transformers.

Standards

• CSA Approved

Construction

• Formed and spot welded from 14 or 16 gauge steel.
• Spot welded Construction and formed edges.
• Removable inner panel.
• Hinged covers.
• 2 cutouts in top of each cabinet with metering plates included.
• Enclosure and cover are finished in ANSI/ASA 61 gray inside and out.

Application

• Designed for indoor use to house controls, instruments and components not requiring oil-tight or dust-tight protection.

Standards

• UL-50 Type 1
• CSA Type 1
• Complies with: NEMA Type 1 & IEC 529, IP30

Construction

• Full swing door using butt hinges.
• Through holes in back for wall mounting.
• Bonding stud is provided on the door and a grounding stud is provided on the box.
• Includes 14 gauge steel inner panel.
• Enclosure and cover are finished in ANSI/ASA 61 gray powder coating.
• Inner panel is finished in white powder coating

Application

• Suitable for use where heat dissipation is required.
• Designed to provide mechanical protection for components requiring ventilation.

Standards

• Complies with NEMA Type 1

Construction

• Base is formed from 16 gauge steel with two 0.5"/0.75" conduit knockouts located in each end.
• Four .125" high raised dimples with mounting holes are provided on the base.
• Cover is formed from 18 gauge steel with 0.235" x 1.5" ventilating slots (0.199" x 1.12" on E & G only).
• Screw holes and offsets in the cover allow easy assembly.
• Base and cover are Finished in ANSI/ ASA 61 gray powder coating.

Application

• Designed for use as a wiring/junction box.
• Provides protection against rain, sleet, snow and dripping water.

Standards

• UL-50 Type 3R & CSA Type 3R
• Complies with: NEMA Type 3R & cUL Type 3R & IEC 60529, IP32

Construction

• Formed and spot welded from 16 or 14 gauge galvanized steel.
• Drip shield top and seam-free sides, front and back.
• 16 gauge galvanized steel continuous hinge has stainless steel pin.
• Cover fastened with captive plated screws.
• Padlocking hasp. & External mounting feet.
• Collar studs provided for mounting optional panels.
• Oil resistant gaskets are permanently secured.
• Enclosure and cover are finished inside and out in ANSI/ASA 61 gray powder coating.