Hammond Manufacturing

Home   >   Products   >   ROLEC   >   Plastic   >   Enclosures

(800) 894-0412       (888) 723-4773 (Fax)
info@clrwtr.com

• Electronic instrument enclosures, designed for mounting printed circuit boards or DIN rail mounted components.
• The polycarbonate material carries a UL flammability rating of UL94 5V and is suitable for outdoor use.
• Lid and mounting holes are located outside of the gasket seal.
• Lid is secured with self captivating M4 stainless steel machine screws (included), threaded into integral stainless steel bushings (for repetitive assembly & disassembly).
• Heavy duty 16 gauge galvanized steel panels available

If you are looking for Hammond Manufacturing Electronic Enclosure, please call us on (800) 894 - 0412 or email us at info@clrwtr.com we will do our best to help you find the Hammond Plastic Enclosures that you are looking for at the most competitive prices possible. If you are searching for Hammond Manufacturing Plastic Enclosure technical information (data-sheets) please use the datasheets or product selection guide page links.

• Molded in general purpose ABS plastic or polycarbonate material.
• The general purpose ABS plastic carries a UL flammability rating of UL94HB. Not recommended for outdoor use.
• Color is light gray (RAL 7035)
• Gasketed lid with two piece "tongue & groove" construction provides protection against access of oil, dust and water.
• Designed to meet IP66 & NEMA 4, 4X, 12 & 13 ratings

• Miniature electronic enclosures, ideally suited for mounting small printed circuit boards.
• Molded in a choice of black or grey general purpose ABS plastic.
• 2 P.C. board standoffs molded into interior.
• Lap joint construction provides protection against access of dust and splashing water.
• Designed to meet IP54
• Two versions available (with or without key ring kit)
• Models with key ring kit are predrilled in narrow side.

• Ideally suited for modern styling or where internal components need to be visible.
• Molded in flame retardant, easy to machine, translucent polycarbonate (material carries a UL flammability rating of 94V-0).
• Integral card guides accept 1.5 mm (0.062") P.C. cards.
• Ice blue version is almost totally transparent to blue, white and near white LEDs, readouts & displays.
• Crystal Clear version is almost totally transparent
• IR Red version is almost totally transparent to infrared devices.
• Lid is secured with M3 x 10 mm Philips machine screws, threaded into tapped integral brass bushings.

• Ergonomically designed for a comfortable fit into the user's hand.
• Perfect for instrument or mobile data enclosures requiring a keypad and display.
• Available with either a solid display area (1592ETSD) or a versatile opening with a clear lens (1592ETCD).
• 1592ETSD offers a solid display area 122 mm x 85 mm (4.8" x 3.4") that will accommodate display boards up to 118 mm x 60 mm (4.6" x 2.37").
• 1592ETCD offers a clear polycarbonate lens 102 mm x 45 mm (4.0" x 1.77") and a plain mylar mask kit allowing for installation of a wide variety of display boards. The lens fits snugly into the case and provides protection from dirt and dust.

• Electronic instrument enclosures, ideally suited for mounting printed circuit boards.
• Ergonomically designed for a comfortable fit into the user's hand.
• Two piece lap joint construction provides protection against dust accumulation and splashing water.
• Molded in a choice of black or grey general purpose ABS plastic.
• Unit is secured with self-tapping screws.

• Rugged electronic instrument enclosures, designed for mounting printed circuit boards. Heavy duty with an average wall thickness of .12" (3.1 mm)
• Molded in flame retardant ABS plastic (material carries a UL flammability rating of 94V-0).
• Designed to meet IP54, watertight version meets IP65.
• Countersunk lid is secured with four M3 x 0.5" x 0.71" (18 mm) Philips machine screws threaded into tapped integral brass bushings.
• Stocked in black and grey with matte textured finish.
• Watertight version has a silicon rubber seal.

Features

• Molded in grey, glass reinforced polyester.
• Heavy duty, thick wall design.
• Includes gasketed lid with two piece "tongue and groove" construction.
• Gasket material is Mohogumi rubber (EDPM.) Heat resistance 100-120 degree C, cold -40 degree C.
• Designed to meet IP65.
• North American Mark of Safety - cUL & UL listed. Certified to Nema 4X standards (UL508)

• Molded in ABS plastic with unique rounded sides - two piece molded construction. Top & bottom "snap" together
• Includes molded in keyhole knockout areas (2) for mounting either vertically or horizontally.
• Bottom half includes 6 molded in, P.C. board standoffs

• Attractively styled and ergonomically designed for use as a "hand-held" instrument enclosure.
• Lap joint construction provides protection against access of dust and splashing water.
• Extra deep top and ultra shallow base are specifically designed to enhance the aesthetics of the enclosure and provide the user with flexibility and assembly efficiency.
• Accessory screws for mounting P.C. boards into standoffs P/N 1593ATS50 (qty. 50), P/N 1593ATS100 (qty. 100).
• Two keyhole knockouts are molded into the inside of the base to facilitate wall mount installation.

• Desk top electronic instrument enclosure, ideally suited for mounting printed circuit boards.
• Two piece construction. Integral card guides accept 1.5 mm (0.062") P.C. cards. 0.20" diameter stand off bosses in the base for supporting various subassemblies.
• Integral brass bushings with four M3 x 0.5" x 8 mm (0.31") Philips pan head machine screws hold recessed panel into sloping front of case.
• 1.01 mm (0.04") aluminum panel with paper on one side.
• Four self-adhesive feet included. Stocked in black and grey.

• One piece molded construction.
• Molded from black general purpose ABS plastic.
• Temperature rated -20º to +94º C.
• 1.0 mm (0.04") wall thickness.

• Two sets of vertical 1.5 mm (0.062") P.C. board guides are molded into case halves front and rear.
• Front and rear panels are 1.6 mm (0.064") brushed aluminum with protective paper on one side.
• Cases halves are secured with M3 x 0.5" x 10 mm (0.39") Philips machine screws threaded into tapped integral brass bushings.
• Integral horizontal P.C. card mounts on Eurocard centers.
• Stocked in matte textured black and grey.
• EMI/RFI shielded cases are stocked in black

• Choice of two versions (with or without battery door and compartment) - in two sizes - in six color combinations.
• Molded in general purpose ABS plastic with a soft grey or black overmold soft plastic grip.
• Top cover is recessed for membrane display or keypad.
• P.C. board standoffs are molded into case.
• Includes removable front panel (for easy modifications) and assembly hardware.
• Battery door & compartment version includes 4 battery clips (for 2 - AA batteries) and a 9 volt (PP3) battery clip.
• Choice of five enclosure colors: light grey, black, red, yellow and translucent blue.
• Choice of two soft side grip colors (grey and black).

• The Clipper series is a British designed hand held enclosure (originally sold under the West Hyde Enclosures Ltd. name).
• Ideally suited for mounting small printed circuit boards for use in hand held applications.
• Molded in a choice of black (RAL 9005) or grey (RAL 9018) - flame retardant ABS plastic.
• Satin texture finish.
• Complete with top & bottom, removable front panel, battery door (except on the smallest size) and three self tapping screws.
• The top panel has a flat display area, perfect for labels, silk screening, membrane keypads or easily machined.

• The Bench Case is a British designed plastic enclosure.
• The top panel & bottom halves include a flat display area, perfect for labels or silk screening.
• The base is molded with six bosses for easy P.C. board mounting.
• The removable 1.5 mm thick aluminum end pane is securely clamped by the two box halves and easily customized.
• Hole in rear of enclosure for easy cord access.

• Perfect for enclosing instruments or P.C. boards that need to be panel mounted.
• Molded in black (RAL 9005) flame retardant ABS plastic.
• Conforms with DIN 43700.
• Molded guides for two horizontally mounted P.C. boards (1.6 mm thick).
• Includes two front panels - choose between natural aluminum panel or grey tinted acrylic filter panel.
• Complete with plastic bezel and two metal panel mounting clamps with screws.

• Rugged electronic instrument enclosures, ideally suited for mounting printed circuit boards for hand-held, desktop or wall mount applications.
• Molded in polystyrene plastic.
• Assembled with four M3 x 0.5" (13 mm) Philips machine screws (included) threaded into integral brass bushings. Perfect for applications where repetitive assembly and disassembly are required. Screws are hidden in a recess in the base.
• Includes four self tapping screws for internal standoffs.
• Lid is a smooth light grey (RAL 7035) and the bottom is a smooth dark grey (RAL 7012).

Our industrial factory automation supplies distributors warehouse in Boise, Idaho stocks some Hammond Manufacturing products enabling us to further assist you in finding the correct watertight flat lid enclosure for your application in the USA. Whether we have flanged lid enclosure in stock in Boise, Idaho or need to ship direct from Hammond Manufacturing to any USA cities; Clearwater Tech can get wallmount & handheld enclosure to you fast and save money! It will be very helpful if you have the watertight clear lid enclosure part numbers ready, then our sales representatives can provide you with a pricing and availability quote for bottom flange enclosure that you are looking for in seconds. If you do not have the part numbers for hand held enclosure, our application engineers will be able to help you figure out the part numbers and get the price quote to you as soon as possible.