June 14, 2010
ABB Contactors
ABB Group's Low Voltage
contactors and overload relays are suitable for a large variety of applications in building and in industry such as motor
control, heating and ventilating, air conditioning, pumping, lifting equipment, lighting, and process power factor
correction.
Mini Contactors & Relays
|
Toshiba Relays
As a motor overload protection relay, Toshiba Industrial's 2E solid state series is
adjustable from Class 3 through Class 40 to provide optimum protection and to accommodate reduced voltage starting and high
inertia loads. Ground fault and phase reversal modules are available.
|
|
|
|
 |
(800) 894-0412 (208) 368-0415 (Fax)
info@clrwtr.com |
YC Series |
IDEC YC series contactors feature weld-resistant silver alloy contacts, giving them a higher level of
reliability and an extra long life. Contacts are also Cadmium-free for environmental safety. YC overloads feature bimetallic
thermal overload relays directly mounted to the contactor. Plus a full range of accessories are available for this series
including top and side mounting auxiliary contact blocks, coil surge suppressors, timers and more. A mechanical interlock
accessory can be used when using two contactors to reverse a motor, to prevent both sets of contacts closing at the same
time.
|
|
If you are looking for IDEC IEC Contactors, please call us on
(800) 894 - 0412 or email us at
info@clrwtr.com we
will do our best to help you find the IDEC IZUMI Thermal Overload Relays that you are looking for at the lowest prices possible. If
you are searching for IDEC Starters technical information (data-sheets) please use the
IDEC Contactor Datasheets or
Product Selection Guide page links.
Key Features
- 35mm DIN rail or direct panel mounting
- Switching current 5A-300A
- Models available to switch from 1/3HP up to 200HP motors
- Auxiliary contacts available
- 50/60Hz AC coil and DC coil models available
- Silver alloy, Cadmium-free, long-life contacts
- Bimetallic thermal overload relays
- Meets IEC, UL, c-UL and other international standards
- CE marked
|
YS Series |
IDEC YS contactors are used for switching motor. They come in both reversing and non-reversing models and
meet all IEC, UL and c-UL standards. All YS series contactors feature weld-resistant silver alloy contacts, giving them a
high-level of reliability and an extra long life. Both feature bimetallic thermal overload relays directly mounted to the
contactor. Mechanical interlock mechanism prevents the forward and reverse contactor from closing at the same time.
A full range of accessories are available for the YS series including top and side mounting auxiliary
contact blocks, coil surge suppressors, relay interface modules, timers and more.
|
|
Key Features
- 35mm DIN rail or direct panel mounting
- Models available to switch from 1/3HP up to 200HP motors
- Meets IEC, UL, c-UL and other international standards
- Advanced design and materials, special silver-alloy long life contacts
- Cadmium-free contacts for environmental safety
- Available with both forward and reversing starters and contactors
- Bimetallic thermal overload relays
- All contactors and thermal overload relays bear the CE mark
- Dual frequency 50/60Hz AC coils
- DC coil models available
|
SafetyOne FS1A Series |
When you want a straightforward system that's safe, easy-to-use and won't cost an arm and a leg, a
SafetyOne FS1A safety controller is the answer!
Unlike a multiple safety relay system, which requires cumbersome wiring and take up too much space, or
safety PLCs that can be costly and difficult to program, our safety controllers make it easy to consolidate safety
circuits. At the same time they meet safety requirements, save space with minimal wiring and cost customers less money.
FS1A is UL listed, TUV rated and CE marked, as well as meets IEC 61508 integrity level 3, ISO 13849-1 performance level e
and EN954-1 safety category 4.
|
|
SafetyOne can replace up to six safety relay modules with no programming. Easily configure by turning on
a dip switch to 1 of 8 pre-difined logic circuits and one module can connect with various IDEC safety and non safety
components such as Emergency Stop switches, Interlock Switches, pilot lights, sensors and light curtains. With 7 dual
channel safety inputs, 4 safety outputs and multiple non safety inputs, monitor, blanking and solenoid drive outputs,
SafetyOne can simplify your complete safety and logic circuit.
Key Features
- No programming required
- Replaces up to six safety relay modules
- Just select a logic from eight pre-programmed circuits
- One module can connect with various types of safety inputs such as E-stop switches or light curtains
- Easily monitor logic circuit, I/Os and error codes with I/O LEDs and two 7 Segment LED display
- IEC 61508 integrity level 3, ISO 13849-1 performance level e and EN954-1 safety category 4 compliant
|
Our IDEC IEC Contactors distributors warehouse in Boise, Idaho stocks some IDEC products enabling us to further
assist you in finding the correct IDEC IZUMI Contactors for your application in the USA, Canada and Mexico. Whether we have IDEC
Thermal Overload Relays in stock in Boise, Idaho or need to ship direct from IDEC IZUMI to any USA cities; Clearwater Tech can get
IDEC Starters to you fast! It will be very helpful if you have the IDEC Contactors part numbers ready, then our sales
representatives can provide you with a pricing and availability quote for IDEC IZUMI Overload Relays that you are
looking for in seconds. If you do not have the part numbers for IDEC Contactors, our application engineers will be able to help
you figure out the part numbers and get the price quote to you as soon as possible.
|
|
|
 |
|
| Part Number: |
|
|
Can't find a part number?
E-mail Us! |
|
|
