IDEC IZUMI Pushbutton Assembly Instructions
Lamp Installation
Lamps can be replaced in two ways:
- If contacts are accessible (or pushbutton not installed in a panel) then it is easiest to first remove the
Contacts from the operator. This will allow easy access to the
lamp/lamp-holder assembly. Grab lamp, depress slightly, and turn counter clockwise. Lamp can then be removed by pushing it back
through the lamp holder.
- If contacts are not accessible, then the lamp can be replaced by first removing the lens from the operator. Just pull lens
straight out either with a fingernail or optional lens removal tool (MT-101). Lamp/lampholder assembly can then be removed with
lamp removal tool (OR-44). Insert lamp removal tool through operator, depress slightly, turn counter clockwise, then pull
lamp/lamp-holder assembly out. Lamp can then be removed by pushing it back through the lamp holder.
If you are looking for IDEC Switches, please call us on
(800) 894 - 0412 or email us at
info@clrwtr.com we will do
our best to help you find the IDEC Pilot Lights that you are looking for at the most competitive prices possible. If you are searching for
IDEC Switch technical information (data-sheets) please use the IDEC Data Sheets page link.
Engraving Lenses
All buttons and lenses can be engraved directly on the outside surface. Illuminated
lenses also allow for engraving on a plate that is underneath the colored section of the lens. Remove the colored section of the
lens by pulling on the edge while simultaneously unhooking it from the latches on the lens holder. The marking plate will then be
accessible. It can then be engraved or a thin marked insert (such as mylar or paper) can be sandwiched between the marking plate
and colored section of the lens.
Panel Mounting
Before any unit can be mounted into a panel, the contact block must be removed. Slide
metal locking lever and pull contact off. Loosen and remove the locking ring and square anti-rotation ring from the operator and
insert operator through panel cutout from the front of the panel. Slide on anti-rotation ring and tighten locking ring, using
locking ring wrench (MT-001). Slide contact block onto operator, observing TOP marking on both parts. Slide metal locking lever
in direction indicated by LOCK. The yellow plastic safety lever lock can then be snapped onto the locking lever; this will prevent
vibration or maintenance actions from releasing the contact from the operator.
PCB Mounting
Being able to separate the contacts from the operator allows for assembly of the front
panel components (operator and lens) to be performed in tandem with the PC board assembly and soldering. For applications where
multiple rows of pushbuttons are mounted closely together, or where other components may obstruct access to the contact locking
lever, be sure to include access holes in the PC board (refer to PC board layout dimensions for location). Also be sure to allow
for space above and to the side of contact to ensure that no components block the contact block locking lever. PC board pins are
designed to rest on the PCB, take this into consideration to ensure that pins do not short closely spaced traces.
Our IDEC Switch distributors warehouse in Boise, Idaho stocks some IDEC IZUMI Switch products (Idec Switches
IDEC IZUMI Switch Distributors XA XW Switches IDEC Pushbutton Push Buttons IDEC Pilot Lights IDEC Switch Pushbuttons IDEC Switches
Distributor) for your application in the USA (Alabama Alaska Arizona Arkansas California Colorado Connecticut Delaware Florida Georgia Hawaii
Idaho Illinois Indiana Iowa Kansas Kentucky Louisiana Maine Maryland Massachusetts Michigan Minnesota Mississippi Misouri Montana
Nebraska Nevada New Hampshire New Jersey New Mexico New York North Carolina North Dakota Ohaio Oklahoma Oregon Pennsylvania Rhode
Island South Carolina South Dakota Tennessee Texas Utah Vermont Virginia Washington Washington D.C. West Virginia Wisconsin
Wyoming), Canada and Mexico.
Whether we have IDEC Switches in stock in Boise, Idaho or need to ship direct from IDEC IZUMI to any USA cities
(New York Los Angeles Chicago Houston Philadelphia Phoenix San Diego Dallas San Antonio Detroit San Jose Indianapolis San Fransisco
Columbus Austin Baltimore Milwaukee Boston Washington El Paso Seattle Denver Charlotte Fort Worth Portand Oklahoma City Tucson New
Orleans Las Vegas Cleaveland Long Beach Alburquerque Kansas City Fresno Virginia Beach Atlanta Sacramento Oakland Mesa Tulsa Omaha
Minneapolis Honolulu Colorado Springs St. Louis Whichita Santa Ana Pittsburgh Arlington Cincinnati Anaheim Toledo Buffalo St. Paul
Corpus Christi Aurora Raleigh Newark Lexington Fayette Anchorage Louisville Riverside Bakersfield Stockton Birmingham Jersey City
Norfolk Baton Rouge Hialeah Lincoln Greensboro Plano Rochester Glendale Akron Garland Madison Fort Wayne Fremont Scottsdale Montgomery
Shreveport Lubbock Chesapeake Mobile Des Moines Grand Rapids Richmand Yonkers Spokane Augusta Rhichmand Glendale Tacoma Irving
Huntington Beach Arlington Modesto Durham Boise Winston Salem); www.clrwtr.com can get IDEC
Switches to you fast and save money!
It will be very helpful if you have the IDEC Switch part numbers ready, then our sales representatives
can provide you with a pricing and availability quote for IDEC IZUMI Switches that you are looking for in seconds. If you do not
have the part numbers for IDEC Switches, our application engineers will be able to help you figure out the part numbers and get the
price quote to you as soon as possible.
|
