Panasonic Electric Works
Since a red LED, harmless to your eyes, has been incorporated as the beam source, you are free from strict laser safety regulations. Moreover, due to the red LED beam source, the measuring spot is visible, which makes positioning of the object simple. Its emitter and receiver are much smaller compared to those of the amplifier built-in type (LA-510). Hence, they can be installed even in a narrow space inside an automatic assembly machine, etc.
For the analog output, in addition to the span adjustment function, a convenient shift function which enables the analog voltage to be shifted by ±0.5 V has been incorporated.
Beam alignment is easy by using the target label (accessory). Further, the 3-stage stability indicators on the amplifier indicate the incident beam level at a glance.
If analog voltage output of LA-A1 or LA-A1P is shifted, the input range may be exceeded. In that case, use CA2-T5 (input range -10 to +10 V).
If you are looking for Panasonic LA-300 Series Sensors, please call us on (844) 331-9378 or email us at firstname.lastname@example.org we will do our best to help you find the Panasonic LA-305 series sensor that you are looking for at the most competitive prices possible. If you are searching for Panasonic LA-310 series beam sensors technical information (data-sheets) please use the datasheets or product selection guide page links.
The external synchronization input controls the timing or the effective duration of the two comparative outputs. Either edge or gate trigger is selectable.
The sensor's output is proportional to the amount of the LED light received. Since there is some variation in the light intensity at the center and the periphery of the sensing area, take care that "output = dimension" may not hold.
For stable operation, use the sensor 10 min., or more, after switching on the power supply.
Keep the front faces of the sensor heads free of dust, dirt, metal powder, etc. Should the faces be covered with it, deteriorating its performance, wipe them clean with a soft cloth or blown air.
Make sure that at least one stability indicator lights up when you supply power to the amplifier connected with sensor heads. While aligning sensor heads, if more stability indicators light up, more reliable detection can be obtained.
Beam alignment should be performed prior to any adjustments on the amplifier.
If the bottom face and the side face of the emitter and the receiver are mounted on the same plane surfaces, or if the front faces of the emitter and the receiver of LA-305 are kept parallel and their top face and side face are mounted on the same plane surfaces, beam alignment need not be done.
Our industrial factory automation supplies distributors warehouse in Boise, Idaho USA stocks some Panasonic displacement sensor products enabling us to further assist you in finding the correct SUNX LA-300 sensor in the USA, Canada and Mexico. Whether we have Panasonic LA-305 LED sensors in stock in Boise, Idaho USA or need to get them from Panasonic Electric Works Corporation of America; Clearwater Tech can get SUNX LA-310 sensors to you fast and save you some money! It will be very helpful if you have the Panasonic LA-300 LED sensor part numbers ready, then our sales representatives can provide you with a pricing and availability quote for LA-305 collimated beam sensor that you are looking for in seconds. If you do not have the part numbers for LA-310 sensors, our application engineers will be able to help you figure out the part numbers and get the price quote to you as soon as possible.
VLT dV/dt Filter MCC 102 are differential-mode low-pass filters which reduce motor terminal phase-to-phase peak voltages spikes and reduce the rise time to a level that lowers the stress on the insulation of motor windings. Compared to sine-wave filters, the dV/dt filters have a cut-off frequency above the switching frequency. The voltage at the motor terminals is still PWM pulse shaped, but the rise time and Upeak are reduced. They are smaller,
Projecting Only 2mm in front of the panel, flush mount switches offer a streamlined package, perfect for applications requiring a hygienic surface. A smooth design cuts down on surface area, preventing dust and other particles from accumulating and making regular cleaning and maintenance a breeze. Safe and space-saving, the contact block only protrudes 27.9m behind the panel, compared with 45mm for most conventional 16mm switches.