TURCK / CONTRINEX / SUNX

Home   >   Products   >   Proximity Sensors

(800) 894-0412       (208) 368-0415 (Fax)
info@clrwtr.com

TURCK UPROX Barrel Sensor, inductive sensing mode; M12 x 1; 10 to 30 VDC; 200 mA (Max.); Shielded; Brass

• Choice of Barrel with Potted-In Cable or M8 (picofast), M12 (eurofast) Quick-Disconnect
• Short Circuit and Overload Protection Incorporated
• Enclosure meets NEMA 1, 3, 4, 6, 13 and IEC IP67
• Reverse Polarity and Wire Break Protection
• Normally Open Output, LEDs Indicate: Output Energized and Short Circuit Warning, & Embeddable

If you are looking for Proximity Sensors, please call us on (800) 894 - 0412 or email us at info@clrwtr.com we will do our best to help you find the Proximity Switches that you are looking for at the lowest prices possible. If you are searching for Proximity Sensor technical information (data-sheets) please use the Proximity Sensor Datasheets page link.

(800) 894-0412       (208) 368-0415 (Fax)
info@clrwtr.com

Functioning according to classical technology, CONTRINEX Inductive Proximity Switches 620 series basically correspond to those of the 300, 400, 420 and 600 series. Switching-wise, they have been optimized in such a way that an increased operating distance can be achieved, especially for small sizes. Users will find them interesting, since with a relatively small markup in price, a valuable increase in operating distance can be obtained.

• M30 and cuboid devices
• Standard devices
• Devices with long operating distance
• All-metal devices
• Cuboid devices: 40x40 mm, 40x120 mm, 60x80 mm and 80x100 mm

(800) 894-0412       (208) 368-0415 (Fax)
info@clrwtr.com

The GA-311 Series Of SUNX inductive proximity sensors provides a high performance solution in a full-featured separate amplifier configuration. With a 3.3kHz response frequency, the GA-311 series is suitable for high-speed metal sensing applications. All of the sensor heads are IP67g rated, so they are resilient in harsh environments including water, oil, dust, or dirt. Sensor heads range from the ultra small GH-2SE, with a 2.8mm diameter, to the long range GH-F8SE, with a detecting distance of 4mm.

(800) 894-0412       (208) 368-0415 (Fax)
info@clrwtr.com

SIE Proximity Capacitive Sensors

• Housings made of metal or plastic
• Compact sizes with potentiometer starting at Ø 6.5 mm
• Sensing distance up to 25 mm
• Flush mount
• Standard 2M cable or quick-disconnect
• DC, AC or AC/DC versions

ABB inductive sensors are not impaired by light, noise, non conductive dust or fluids, such as oil. They detect precisely and without the need for adjustment and also offer largely standardised parameters. There are two parts which make up the wireless ABB proximity switch: the head of an inductive sensor in different dimensions and the communication module which is identical for all sensor head variants. The communication module is connected conventionally to the ABB proximity sensor head like a standard sensor plug.

Red Lion Controls Inductive Proximity Sensors detect the presence of metal objects that come within range of their oscillating field and provide target detection to "zero speed". Internally, an oscillator creates a high frequency electromagnetic field (RF) that is radiated from the coil and out from the sensor face. When a metal object enters this field, eddy currents are induced into the object. As the metal moves closer to the Red Lion proximity sensor, these eddy currents increase and result in an absorption of energy from the coil that dampens the oscillator amplitude until it finally stops. These Red Lion Controls Inductive Proximity Switches have a maximum sensing distance of 0.078" (2 mm) and 0.393" (10 mm) respectively, and operate over a wide power supply range.

The Red Lion Proximity Sensors are each housed in plastic with a top active face. The NPN transistor outputs are true open collector and are compatible with most Red Lion counter and rate meter input circuits. Maximum sensing frequencies are 2 KHz and 500 Hz respectively. In addition, the outputs are overload and short circuit protected. These sensors are shielded for flush mounting in metal applications.