Red Lion Controls
The IRMA accepts a 2, 3, or 4 wire RTD or resistance input and converts it into a 4 to 20 mA current output.
The 4 to 20 mA output is linearly proportional to the temperature or the resistance input. This output is ideal for interfacing to indicators, chart recorders, controllers, or other instrumentation equipment.
The IRMA is loop-powered which means that the same two wires are carrying both the power and the output signal. The unit controls the output current draw from 4 to 20 mA in direct proportion to the input while consuming less than 4 mA for operation. The conversion to a current output signal makes the IRMA less susceptible to noise interference and allows accurate transmission over long distances. Two-Way isolation allows the use of grounded RTD's which can provide additional noise reduction benefits.
If you are looking for Red Lion IRMA RTD Modules, please call us on (844) 331-9379 or email us at email@example.com we will do our best to help you find the Red Lion IRMA Intelligent RTD Module with Analog Output that you are looking for at the most competitive prices possible. If you are searching for Red Lion Controls IRMA DC RTD Module with Analog Output technical information (data-sheets) please use the datasheets or product selection guide page links.
The IRMA uses an eight position DIP switch to accomplish the input sensor configuration, range selection, and unit calibration. A simple range setting technique (Field Calibration) is used so the actual input signal adjusts the output current for scaling. This technique eliminates the need for potentiometers which are vulnerable to changes due to vibration.
The unit is equipped with a universal mounting foot for attachment to standard DIN style mounting rails, including top hat rail (T) according to EN 50 022 - 35 X 7.5 and 35 X 15, and G profile according to EN 50 035 - G 32.
The IRMA is DC powered. The DC power input is isolated from the signal input and analog output. The unit scales the analog output proportionally to the RTD or resistance input signal. The analog output may be configured for one of the following: 0 to 20 mA, 4 to 20 mA, or 0 to 10 VDC. Making the signal conversion with the IRMA to a current output signal, makes the signal less susceptible to noise interference and allows accurate transmission over long distances. The 3-Way isolation allows the use of grounded RTD's which can provide additional noise reduction benefits.
All safety related regulations, local codes and instructions that appear in the manual or on equipment must be observed to ensure personal safety and to prevent damage to either the instrument or equipment connected to it. If equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.
The output can be set to go Upscale or Downscale for the detection of an open sensor. The nominal values for each output range are listed under RTD Break Detection in the Specifications section. This setting is always active, so changes to the setting are effective immediately.
If the unit has scaling problems (output remains at -0.5 mA, 3.5 mA, or -0.5 VDC nominal), check the ERROR LED on the front of the unit. An E2PROM problem is indicated when the ERROR LED is on. If the ERROR LED is on, perform a Basic Calibration followed by a Field Calibration. Turn the power off for 5 seconds. Turn power on and check if the ERROR LED is on. If the LED is on, contact the factory.
|Intelligent RTD Module||IRMA2003|
|Intelligent RTD Module||IRMA3035|
Our industrial automation supplies distributors warehouse in Boise, Idaho stocks some Redlion Controls products enabling us to further assist you in finding the correct IRMA2003 RTD module for your application in the USA. Whether we have IRMA3035 modules in stock in Boise, Idaho or need to ship direct from Red Lion Controls to any USA cities; Clearwater Tech can get IRMA intelligent RTD module with analog output to you fast and save some money! It will be very helpful if you have the IRMA DC RTD module part numbers ready, then our sales representatives can provide you with a pricing and availability quote for IRMA RTD modules that you are looking for in seconds. If you do not have the part numbers for IRMA DC intelligent RTD module with analog output, our application engineers will be able to help you figure out the part numbers and get the price quote to you as soon as possible.
The DT Series of temperature compensated DC current transducers is ideal for energy management system inputs where the controller is designed to accept 333 mV signals, commonly found in power monitoring applications. Other output options avalable are a 0-5 VDC signal used in building energy management systems or 0-10 VDC seen more often in industrial controllers. Additionally, this series features a patent-pending method that improves
The Latching medium voltage three-phase indoor vacuum contactor uses separate coils and mechanisms to both close and open the vacuum bottle contacts (termed as; mechanically held or latching, contacts). Motortronics 7.2kV Class, 'Non-Latching' and 'Latching' Series of medium voltage three-phase indoor vacuum contactors can be used in power systems with a rated voltage of up to 7.2 kV and can be used for continuous AC operating currents of up to 400 amperes.