Red Lion Control's new PSDR series of 24 VDC power supplies are industrial input voltage supplies available in 1, 2 and 4 Amp versions. PSDR Red Lion Power Supplies can accept an input voltage range from 85 to 264 VAC or 90 to 350 VDC and feature primary switched-mode regulator technology. They offer low output ripple and an adjustable output voltage from 22.5 to 28.5 VDC. The output is electronically protected against overloads and short circuits. The Red Lion Controls power supply modules snap onto standard 35 mm flat DIN rails and use removable terminal blocks for easy wiring.

If you are looking for Red Lion Power Supply, please call us on (800) 894 - 0412 or email us at info@clrwtr.com we will do our best to help you find the Red Lion Power Supplies that you are looking for at the lowest prices possible. If you are searching for RedLion Control Power Supply technical information (data-sheets) please use the Red Lion Data Sheets page link.

The Model APSIS is a convenient plug-in unregulated +24 VDC Red Lion power supply designed to "load share" when connected in parallel with other +24 VDC unregulated systems with unusual power requirements due to sensor or accessory loading. It can also be used as a general purpose standalone supply to power +24 VDC control circuits, sensors and accessories. In addition, two 20 mA Current Source outputs are available, each capable of powering up to 16 Serial Communications units. The APSIS Red Lion Power Supply is available in 115 and 230 VAC ±10%, 50/60 Hz. primary supply. Operating temperature range is -20C to +50C. The Red Lion power supplies feature CE, UL and CUL approvals, making them ideal for your next industrial application.

8 Apollo Thermocouples (APLTC) and 8 GEMINIs, all with isolated 20 mA Current Loop Serial Communications, monitor and control processes within a plant. All units, which are located in different areas of the plant, are tied together in series in two "Loops" (one Transmit Tx, the other Receive Rx) and are connected to a Central Pro-Face Xycom Computer located in another area of the plant. Since there are more than 7, and no more than 16 units in the "Loop", the APSIS +20 mA Current Source Outputs are used to power each "Loop". (Both Apollo Thermocouple and Gemini units can power up to 7 units in a "Loop" when using their internal 20 mA sources. However, their sources may not be tied together to power more than 7 units.) Each unit is assigned a different address number and the same Baud rate. An application program is written which allows the Central Computer to send and retreive data from any APLTC or Gemini.

The Model MLPS1 is a +12 VDC Red Lion Controls power supply designed to attach to the rear of the Micro-Line Series. The MLPS1 Red Lion power supplies can be powered from an 85-250 VAC source. Caution: The maximum output current of the MLPS is 400 mA. Check the specifications of the specific Red Lion Counter(s)/indicators(s) and sensors(s) being used to ensure that total current requirements do not exceed 400 mA.

All safety related regulations, local codes and instructions that appear in the manual or on equipment must be observed to ensure personal safety and to prevent damage to either the instrument or equipment connected to it. If equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. The Redlion power supply unit should be installed in a location that does not exceed the maximum operating temperature and provides good air circulation. Placing the unit near devices that generate excessive heat should be avoided. The MLPS1 Red Lion power supply is shipped with all the necessary hardware to mount to the rear of an installed Micro-Line unit. Refer to the instructions that correspond to your Micro-Line unit for proper installation.

Our Red Lion Controls distributors warehouse in Boise, Idaho stocks some RedLion Controls products (PSDR PSMA MLPS1 Red Lion Power Supply APS APSIS Red Lion Controls Power Supplies Distributors) enabling us to further assist you in finding the correct Red Lion Controls power supply for your application in the USA (Alabama Alaska Arizona Arkansas California Colorado Connecticut Delaware Florida Georgia Hawaii Idaho Illinois Indiana Iowa Kansas Kentucky Louisiana Maine Maryland Massachusetts Michigan Minnesota Mississippi Misouri Montana Nebraska Nevada New Hampshire New Jersey New Mexico New York North Carolina North Dakota Ohio Oklahoma Oregon Pennsylvania Rhode Island South Carolina South Dakota Tennessee Texas Utah Vermont Virginia Washington Washington D.C. West Virginia Wisconsin Wyoming), Canada and Mexico.

Whether we have Red Lion Power Supply in stock in Boise, Idaho or need to ship direct from Red Lion Controls to any USA cities (New York Los Angeles Chicago Houston Philadelphia Phoenix San Diego Dallas San Antonio Detroit San Jose Indianapolis San Fransisco Columbus Austin Baltimore Milwaukee Boston Washington El Paso Seattle Denver Charlotte Fort Worth Portand Oklahoma City Tucson New Orleans Las Vegas Cleaveland Long Beach Alburquerque Kansas City Fresno Virginia Beach Atlanta Sacramento Oakland Mesa Tulsa Omaha Minneapolis Honolulu Colorado Springs St. Louis Whichita Santa Ana Pittsburgh Arlington Cincinnati Anaheim Toledo Buffalo St. Paul Corpus Christi Aurora Raleigh Newark Lexington Fayette Anchorage Louisville Riverside Bakersfield Stockton Birmingham Jersey City Norfolk Baton Rouge Hialeah Lincoln Greensboro Plano Rochester Glendale Akron Garland Madison Fort Wayne Fremont Scottsdale Montgomery Shreveport Lubbock Chesapeake Mobile Des Moines Grand Rapids Richmand Yonkers Spokane Augusta Rhichmand Glendale Tacoma Irving Huntington Beach Arlington Modesto Durham Boise Winston Salem); www.clrwtr.com can get Red Lion Power Supply to you fast!

It will be very helpful if you have the Red Lion Power Supplies part numbers ready, then our sales representatives can provide you with a pricing and availability quote for Red Lion Controls power supply that you are looking for in seconds. If you do not have the part numbers for RedLion Power Supply, our application engineers will be able to help you figure out the part numbers and get the price quote to you as soon as possible.