(800) 894-0412       (208) 368-0415 (Fax)
info@clrwtr.com

RELECO general purpose relays are used for most general applications, such as automation, pneumatic, heating appliances, signaling, as an input or output interface, etc.

• Change-over contacts
• Isolation between N.O. / N.C.: 1000 Vrms
• Gap: 0.5 mm
• Rating loads of up to:
  16 A @ 230 V AC1
  16 A @ 30 V DC1
  0.5 A @ 110 V DC1
  0.2 A @ 220 V DC1

If you are looking for RELECO Relays, please call us on (800) 894 - 0412 or email us at info@clrwtr.com we will do our best to help you find the Comat Timers that you are looking for at competitive prices. If you are searching for RELECO Relay Sockets technical information (data-sheets) please use the RELECO Datasheets OR Product Selection Guide page links.

An open contact arrangement allows an increase in the contact gap, increasing the DC "break capacity" without altering the AC performance.

• Gap: 1.5 mm (QR-C types); 1.7 mm (MR-C)
• Isolation of contacts NO: >2000 Vrms
• Maximum load:
  16 A @ 230 V AC1
  1.2 A @ 110 V DC1
  0.4 A @ 220 VDC1

RELECO Solid State Relays are used to switch up to 50 VDC, heating elements electrovalves, Motors, input/output signals on PLC's, solenoids, incandescent and fluorescent lamps, etc. Inductive loads must be shunted with an antiparallel Diode.

• Range of input voltage 5 - 32 VDC
• Peak inrush voltage protection EC-1000-4-5 level 1
• Max. output current 2 A
• Max. output voltage 50 VDC
• Working temperature, max. 60ºC
• Dielectric strengh input / output 4 KV/1 min.

RELECO relays with twin contacts are used to switch low currents with high operational reliability.

• Change-over contacts
• Isolation between N.O. / N.C.: 1000 Vrms
• Gap: 0.5 mm
• Gold-flashed contact 0.2µ or plated with 10µ Au (optional).
• Maximum load: 6 A @ 230 V AC1
• Minimum load: 1 mA @ 5 V DC1

RELECO sensitive DC relays adjusted to work at lower power, available in both MR-C and QR-C versions.

• Gold-flashed contacts 0.2µ or plated 10µ Au (optional)
• Operational voltage range:
  S relays: 0.8 - 2.5 UN
  E relays: 0.8 - 1.7 UN
  N relays: 0.8 - 1.4 UN

RELECO double make relays are designed to switch high DC loads at voltages of 110 and 220 VDC. If consists of one normally open contact with a gap > 3 mm so that the arc length is divided by two. Isolation between contacts is > 2000 Vrms. X version RELECO double make relays are available in MR-C and QR-C type housing.

Two open contacts, one of silver nickel and one of tungsten work in parallel but are physically displaced so that the tungsten contact makes and breaks the load. The silver contact is used for carrying the stable current. RELECO high inrush current relay was designed to switch incandescent and fluorescent lamps, (with p.f corrected), and DC inductive loads.

• Only available in C7 type housing.
• Maximum loads:
  6 A @ 230 V AC5a/b (lamps)
  10 A @ 230 V AC15; 1.5 A @ 110 V DC1

RELECO magnet blow-out relay versions are similar to X types (Double Make Relays), however they have an addition of a powerful magnet which "blows out" the arc generated when the contacts are opened, therefore quenching the arcing quickly and increasing the contact life. They are able to switch DC loads of up to 10 A @ 222 V DC1 and 2 A @ 220 V DC13

Both RELECO S12 socket and the S10-M are designed to get a homogeneous set with identical terminal disposition, which allows easy identification of the contacts set in each level and simpler wiring. Both A2 Terminals allow a secure interconnection through external bridges among an unlimited number of these sockets or a mixture of S12 and the new S10-M. The A2 terminal, free on both the first and last sockets, is used to connect the cable of common polarity.

The modules CT2 and CT3 are electronic RELECO Timers that are designed to be inserted beween a standard plug-in relay and its socket, enabling the relay to be operated as a timer relay. The CT modules are able to accept any standard 8- or 11-pin RELECO series C2 or C3 as well as those from any other supplier.