 |
(800) 894-0412 (208) 368-0415 (Fax) info@clrwtr.com |
 Model PC-102CICI-DL |
SymCom's PC-102CICI-DL is a Dual seal-Leak detector. The inputs are used to sense seal
failures on pumps. When water is detected, the associated output relay is energized. The input logic may be selected to be
direct or inverted using DIP switches on the side of the device. It has two isolated form-C output relays and two red LEDs
which illuminate when the associated output relay is energized.
|
|
If you are looking for SymCom Pump Controllers, please call us on
(800) 894 - 0412 or email us at
info@clrwtr.com we
will do our best to help you find the SymCom Dual Seal Leak Detectors that you are looking for at the lowest prices
possible. If you are searching for SymCom 5-Channel Pump Controllers technical information (data-sheets) please use the
Pump Controller Datasheets OR
Product Selection Guide page links.
|
 Liquid Level Control Relays |
The PC-xxx-LLC-CZ is a liquid level control relay used to control conductive liquid pumping operations in a
pump-up or pump-down application. The unit comes in two different voltage ranges. The model PC-100-LLC-CZ is for 95-120VAC
applications and the model PC-200-LLC-CZ is for 190-240VAC applications.
The unit has an adjustable sensitivity knob (4.7-100K ohms) that is set according to the resistance level
at which you want the probes (sold separately) to sense the conductive liquid. The unit has a built-in debounce time delay
that prevents the relay from energizing if the probe resistance momentarily goes above or below the sensitivity setpoint (due to
liquid splashing in the tank).
|
 Model PC-105 |
SymCom's PumpControl Model PC-105 is a five-channel pump controller designed to handle
multiple pump applications. Alternatively, it can operate as a 5-channel switch. The PC-105s control functions support all of
the popular industry-standard multi-pump configurations. Using the built-in DIP switches, individual pumps can be disabled
when taken out of service for repair or maintenance.
|
 Model PC-102CICI-LT |
SymCom's PC-102CICI-LT is a seal-Leak and over-Temperature detector. The seal-leak input is
used to sense seal failures on submersible pumps while the temperature input is used to detect motor overheating. Both can be
configured to suit the probes of your choice. It has two form-C isolated output relays and two LEDs, which illuminate when each
associated output relay is energized.
|
 Model 460-15-100-LLS |
The PumpSaver Model 460-15-100-LLS is a liquid level sensor to detect the presence of conductive liquids.
The unit has an adjustable debounce timer (2-60 seconds) to help prevent nuisance relay actuations due to waves or liquid
splashing into the tank. When the probe is submersed, the PumpSaver's output contacts will change state as soon as the debounce
time expires. Relay logic can be inverted so the PumpSaver's output contacts change state when the probe is no longer
submersed.
|
 Model 460-15-100-SLD |
The MotorSaver Model 460-15-100-SLD is a DIN rail or surface mountable seal leak detector used to sense
seal failures on submersible pumps. When the unit is powered and the resistance from the probe is greater than the
sensitivity control level, the internal relay contacts change state. As water leaks into the motor seal, the resistance
measured by the probe decreases. When the resistance drops below the sensitivity control level, the unit will trip and the
relay contacts will change back to their original state.
|
 Model 201-100-SLD |
The MotorSaver Model 201-100-SLD plug-in mount seal leak detector is used to sense seal failures on
submersible pumps. The 201-100-SLD plugs into an OT08-PC or RB08-PC octal socket (sold separately). When the unit is powered
and the resistance from the probe is greater than the sensitivity control level, the internal relay contacts change state.
As water leaks into the motor seal, the resistance measured by the probe decreases. When the resistance drops below the
sensitivity control level, the unit will trip and the relay contacts will change back to their original state.
|
 LLC4 Series |
LLC4 Series Octal Plug-in Single Level Control
- Single Probe Level Control for Conductive Liquids
- Adjustable or Fixed Sensing up to 250,00 Ohms
- 24, 120 or 230VAC Models are Available
- Isolated AC Voltage on the Probes
- 4 Amps Resistive SPDT Isolated Contacts
- Time Delay Prevents Rapid Cycling
- Moisture Protected Circuitry
- 1.78 x 2.39 x 2.9 Inches (45.2 x 60.7 x 73.7 mm)
- UL Recognized, CSA Certified, CE
|
 LLC5 Series |
LLC5 Series Octal Plug-in Dual Level Control
- Dual Probe Level Control for Conductive Liquids
- Onboard Knob or Fixed Sensing up to 100,000 Ohms
- Octal Plug-In Base (see Accessory Sockets)
- LED Indicator Reduces Adjustment Time
- 24, 120, or 230 VAC Models are Available
- 5 Amps SPDT Isolated Contacts
- 1.78 x 2.39 x 3.25 Inches (45 x 61 x 83 mm)
- UL Recognized and CSA Certified, CE
|
 LLC1 Series |
LLC1 Series Open PC Single Level Control
- Single Probe Liquid Level Control for Conductive Liquids
- Isolated AC Voltage on the Probes
- Adjustable or Fixed Sensing up to 250,000 Ohms
- Time Delay Prevents Rapid Cycling
- 0.25 inch (6.35 mm) Male Quick Connect Terminals
- 24 or 120 or 230 VAC Models are Available
- 10 Amps SPDT Isolated & SPST Non-isolated Contacts
- Clear Coated Electronics
- 0.50" (12.7 mm) Nylon Standoffs, #6 Screws
- 3.5 x 2.75 x 2.00 Inches (88.9 x 69.9 x 50.8 mm)
- UL Recognized, CSA Certified, CE
|
 LLC2 Series |
LLC2 Series Open PC Dual Level Control
- Dual Probe Liquid Level Control for Conductive Liquids
- Isolated AC Voltage on the Probes
- Adjustable or Fixed Sensing up to 100,000 Ohms
- Terminal Block or Quick Connect Terminals
- 24, 120, or 230 VAC Models are Available
- 10 Amps SPDT Isolated Contacts
- Clear Coated Electronics
- 0.50" (12.7 mm) Nylon Standoffs, #6 Screws
- 3 x 4 x 1.88 Inches (76 x 102 x 48 mm)
- UL Recognized, CSA Certified, CE
|
 LLC6 Series |
LLC6 Liquid Level Control - Low Level Cutoff
- Designed for Low Level Cutoff Protection
- Energized on Wet Probe
- Fixed Time Delay of 1 to 60 seconds
- Sense Resistance of 5k to 250k Ohms
- 24, 120, or 230 V AC Input Voltages Available
- 10 A, SPDT Relay Contacts
- UL Recognized, CSA Certified, CE
|
 LLC8 Series |
LLC8 Liquid Level Control - Low Level Cutoff
- Designed for Low Level Cutoff Protection
- Energized on Wet Probe
- Fixed Time Delay of 1 to 60 seconds
- Fixed Sense Resistance of 5k to 250k Ohms
- 24, 120, or 230 V AC Input Voltages Available
- Isolated 10 A, SPDT Relay Contacts
- UL Recognized, CSA Certified, CE
|
|
Our SymCom distributors warehouse in Boise, Idaho USA stocks some SymCom PumpSaver products enabling us to
further assist you in finding the correct SymCom Microcontroller Based Pump Controllers in the USA. Whether we have SymCom
PumpSaver Pump Controllers in stock in Boise, Idaho USA or need to ship direct from SymCom to any USA cities; Clearwater Tech can
get SymCom Model PC-102CICI-LT Pump Controllers to you fast and save you some money! It will be very helpful if you have the
SymCom Pump Controllers part numbers ready, then our sales representatives can provide you with a pricing and availability quote
for SymCom Model PC-105 Five-Chanel Pump Controller that you are looking for in seconds. If you do not have the part numbers for
SymCom Model PC-102CICI-DL Dual Channel Switches, our application engineers will be able to help you figure out the part numbers
and get the price quote to you as soon as possible.
|