June 03, 2011
SSAC Current Sensors
The ECS Series
of Single Phase AC Current Sensors is a universal, overcurrent or undercurrent sensing control. Its built-in toroidal sensor
eliminates the inconvenience of installing a stand-alone current transformer. Includes onboard adjustments for current sensing
mode, trip point, and trip delay. Detects over or under current events like locked rotor, loss of load,
|
NK Current Switches
The AS3 Series
current sensing switches provide the same dependable indication of status offered by the AS1 Series current sensing switches, but
with the added benefit of increased setpoint accuracy. A choice of three, jumper-selectable input ranges allows the AS3 current
sensing switch to be tailored to an application, providing more precise control through improved setpoint resolution.
|
|
|
|
 |
(800) 894-0412 (208) 368-0415 (Fax)
info@clrwtr.com |
Model RM-1000 |
SymCom RM-1000 is a motor monitoring device to be used in conjunction with
Model 777 MotorSavers, Model 777-KW/HP PumpSaver, Model 77C MotorSaver and
Model 601 MotorSaver. The RM-1000/777 motor management system combines unsurpassed electronic motor protection and critical,
user-friendly motor monitoring. The RM-1000 improves safety for service and operations personnel because the overload
can be controlled, status monitored, and setpoints can be changed without opening the control panel. Using the RM-1000 is a
simple, cost effective way of satisfying the new requirements for arc flash safety.
|
|
If you are looking for SymCom Remote Monitors, please call us on
(800) 894 - 0412 or email us at
info@clrwtr.com
we will do our best to help you find the SymCom PumpSaver Model RM-1000 Remote Monitors that you are looking for at the
most competitive prices possible. If you are searching for SymCom MotorSaver RM-2000 Remote Monitor technical information
(data-sheets) please use the datasheets or product selection guide page links.
|
Model RM-2000 |
SymCom RM-2000 is a motor monitoring device to be used in conjunction with SymCom's Model 777. The
RM-2000/777 motor management system combines unsurpassed electronic motor protection and critical, user-friendly motor
monitoring. The RM-2000 has membrane keypad controls which allow both monitoring and control of a 777 MotorSaver through a
RS-485 network using Modbus RTU protocol. A second communication port is standard and allows monitoring and control of up to
99 RM-2000 devices from a PLC, DCS, or SCADA system or a PC with solutions software installed. The RM-2000 is environmentally
protected and is easily mounted on the front of a panel or MCC.
|
Model RM-2000-CBM+ |
SymCom RM-2000 Coal Bed Methane Special / 777 combination optimizes gas production from coal bed methane
wells while protecting the submersible pump. The 777 provides unmatched pump protection while the RM-2000 CBM Special cycles
the pump based on pressure measurements from one or two 4-20 mA pressure transducers. The first transducer measures down hole
pressure while an optional second transducer can be used to measure annulus pressure (gas pressure). The second transducer
corrects head measurements caused by high annulus pressure. The pump is started when the maximum head set point is crossed
and stopped when the minimum head set point is crossed.
|
Model RM-2000-RTDW |
The RM-2000-RTDW motor-monitoring device can be used to monitor and/or control SymCom's Model 777
via an RS-485 Modbus Network. Two form C output relays are available
for an RTD alarm and a warning alarm. Alarm and trip levels can be set for each RTD to activate the RTD alarm and
deactivate the 777 output relay respectively. In addition, the RM-2000-RTDW has two inputs: one to connect to a
ground-fault module and the other for connection to a remote reset button. A second communication port allows monitoring
and control of up to 99 RM-2000-RTDW devices from a computer with SymCom's Solutions software, or a PLC, DCS, or SCADA
system. The RM-2000-RTDW is environmentally protected and can easily be mounted on the front of a panel or MCC.
|
|
Our industrial automation supplies distributors warehouse in Boise, Idaho USA stocks some SymCom products
enabling us to further assist you in finding the correct MotorSaver Model RM-1000 remote monitoring device in the USA, Canada
and Mexico. Whether we have MotorSaver remote monitor in stock in Boise, Idaho USA or need to ship direct from SymCom SSAC to
any USA cities; Clearwater Tech can get SymCom remote monitor RM-2000 to you fast and save you some money! It will be very
helpful if you have the SymCom remote monitors part numbers ready, then our sales representatives can provide you with a
pricing and availability quote for Motor Saver RM-2000 CBM+ that you are looking for in seconds. If you do not have the part
numbers for PumpSaver remote monitors, our application engineers will be able to help you figure out the part numbers and get
the price quote to you as soon as possible.
|
|
|
|
 |
|
| Part Number: |
|
|
Can't find a part number?
E-mail Us! |
|
|
