SymCom

Home   >   Products   >   SymCom MotorSaver & PumpSaver

(800) 894-0412       (208) 368-0415 (Fax)
info@clrwtr.com

SymCom 777 Overload Relay can be used on any 190-480VAC, 3-phase system drawing 2-800A and will protect motors against the following damaging conditions: overload, underload, jams, undervoltage, overvoltage, single-phasing, voltage and current unbalance, ground fault (Class II), rapid cycling and phase reversal.

If you are looking for SymCom MotorSaver, please call us on (800) 894 - 0412 or email us at info@clrwtr.com we will do our best to help you find the SymCom PumpSaver Overload Relays that you are looking for at the lowest prices possible. If you are searching for SymCom MotorSaver Remote Monitors technical information (data-sheets) please use the SymCom Datasheets OR Product Selection Guide page links.

SymCom RM-1000 is a motor monitoring device to be used in conjunction with SymCom's Model 777 MotorSaver, Model 777-KW/HP PumpSaver, Model 77C MotorSaver and Model 601 MotorSaver. The RM-1000/777 motor management system combines unsurpassed electronic motor protection and critical, user-friendly motor monitoring. The RM-1000 improves safety for service and operations personnel because the overload can be controlled, status monitored, and setpoints can be changed without opening the control panel. Using the RM-1000 is a simple, cost effective way of satisfying the new requirements for arc flash safety.

SymCom Model 80 is designed to continuously monitor phase rotation of 3-phase systems. Critical applications include fan motors, scroll compressors, grinders, conveyor systems, elevators and escalators. A solid-state sensing circuit drives an internal Electro-Mechanical Relay which is energized when proper phase rotation is applied. An LED indicator illuminates when phase rotation is correct. Reset is automatic.

SymCom Model 460-XXX-SP protects single-phase motors from damage caused by low and high voltage and rapid cycling. Controls are provided to set the nominal voltage (190-240VAC) and the desired restart delay time (1-500 sec.). A unique microcontroller-based, voltage-sensing circuit constantly monitors the voltage to detect harmful power line conditions.

When a harmful condition is detected, the MotorSaver's output relay is deactivated after a specified trip delay. The output relay reactivates after Power Line Conditions return to an acceptable level for a specified amount of time (restart delay). The restart delay is also a power-up delay and can be utilized to stagger-start motors on the same system. The trip delay prevents nuisance tripping due to rapidly fluctuating power line conditions.

SymCom Model ISS-100 isolated Switch is UL 913 listed as an associated apparatus for interfacing between hazardous and non-hazardous areas. The ISS-100 must be installed in a non-hazardous area.

SymCom Model 520CS is a fully programmable, microcontroller-based, current sensing device designed to monitor three phase pumps. Unlike the Model 520CP which is designed to work with Motors that have ramp up times of 4 seconds or less, the Model 520CS has a programmable motor acceleration time that can be set from 0-50 seconds.

Three External Current Transformers must be utilized in conjunction with the Model 520CS. The following 9 trip points can be set and viewed from the three digit alphanumeric LED: overcurrent trip point, undercurrent trip point, current unbalance trip point, trip delay, rapid cycle timer (RD1), overload restart delay (RD2), underload restart delay (RD3), number of starts after a fault, and motor acceleration time.

SymCom Model ALT alternating relays are used to alternate between two loads. The ALT is commonly used in duplex pumping applications to balance the runtime of both pumps. The Model ALT-S is used in single high level float applications. When the float switch opens, the alternating relay changes state forcing the other pump to run the next time the float closes. The Model ALT-X has an internal cross-connected relay and is used in applications where two high level floats are used. These floats are commonly referred to as lead and lag floats. The lead float causes the relay to change state each time it opens (identical to the float in the ALT-S application).

SymCom's PC-102CICI-DL is a Dual seal-Leak detector. The inputs are used to sense seal failures on pumps. When water is detected, the associated output relay is energized. The input logic may be selected to be direct or inverted using DIP switches on the side of the device. It has two isolated form-C output relays and two red LEDs which illuminate when the associated output relay is energized.

SymCom's Model 231-INSIDER-P single-phase PumpSaver Plus fits inside 1/3, 1/2, 3/4, and 1hp 230V control boxes and is designed to protect single-phase pumps from dry-well, dead-head, jammed impeller, rapid-cycle, overvoltage, and undervoltage conditions.

The Insider communicates with a hand-held diagnostics tool called the Informer (sold separately). The Informer displays 15 parameters including calibration points, trip points, running points, and last faults. An IR Kit-12 (12" fiber optic kit) is included with each Insider, allowing the Informer to access these parameters even when the Insider is enclosed in a control box. This is valuable for troubleshooting the pump while it is running.

The Model LSRX is an AC current sensor designed to energize the output contact whenever 4.5 Amps or greater is present. The LSRX is used commonly as an AC current proof relay to indicate if a motor is operating. It can also be used to interlock fans, compressors, and motors; to indicate equipment status such as feed rates, tool wear, loss of prime on pumps, mixer viscosity, and all types of current sensing conditions; or to stage pump motors, chillers, or other machinery.

SymCom T-10 On-Delay Timer is a solid-state electronic device that provides accurate and reliable timing for control circuits up to 600 VAC. The T-10 features a user selectable time delay from 6 seconds to 10 minutes, and SPDT output contacts. When power is applied to the T-10, it immediately begins its timing cycle. During this time, the indicator LED alternates between red and green, and the output contacts remain inactive. When the timing cycle is complete, the indicator LED turns solid green, and the output contacts are activated. The output contacts will remain activated until power is removed from the T-10.

SymCom offers a wide array of current transformers.

• Voltage class: 600V
• BIL rating: 10kV
• CT-xxx (xxx:5 current ratio)
• D/F (D-Donut Style, F-Footed Style)
• 10/20/30 (10-1.0" window; 20-2.0" window; 30-3.0" window)

Enclosures Part Numbers:

• NEMA 3R-L 6" x 6" x 4" with lenses to view the PumpSaver
• NEMA 3R Steel 6" x 6" x 4" fits all PumpSaver models
• MotorSaver models 102A, 250A, 350, 355 and 455

Our SymCom distributors warehouse in Boise, Idaho USA stocks some SymCom products (SymCom MotorSavers PumpSavers Overload Relays Power Remote Voltage Current Monitors Load Sensors Intrinsically Safe Alternating Relays Pump Controllers Timers Current Transformers Communication Modules Distributors) enabling us to further assist you in finding the correct SymCom MotorSaver Overload Relays in the USA (Alabama Alaska Arizona Arkansas California Colorado Connecticut Delaware Florida Georgia Hawaii Idaho Illinois Indiana Iowa Kansas Kentucky Louisiana Maine Maryland Massachusetts Michigan Minnesota Mississippi Missouri Montana Nebraska Nevada New Hampshire New Jersey New Mexico New York North Carolina North Dakota Ohio Oklahoma Oregon Pennsylvania Rhode Island South Carolina South Dakota Tennessee Texas Utah Vermont Virginia Washington Washington D.C. West Virginia Wisconsin Wyoming), Canada and Mexico.

Whether we have SymCom PumpSavers in stock in Boise, Idaho USA or need to ship direct from SymCom to any USA cities (New York Los Angeles Chicago Houston Philadelphia Phoenix San Diego Dallas San Antonio Detroit San Jose Indianapolis San Francisco Columbus Austin Baltimore Milwaukee Boston Washington El Paso Seattle Denver Charlotte Fort Worth Portland Oklahoma City Tucson New Orleans Las Vegas Cleaveland Long Beach Alburquerque Kansas City Fresno Virginia Beach Atlanta Sacramento Oakland Mesa Tulsa Omaha Minneapolis Honolulu Colorado Springs St. Louis Whichita Santa Ana Pittsburgh Arlington Cincinnati Anaheim Toledo Buffalo St. Paul Corpus Christi Aurora Raleigh Newark Lexington Fayette Anchorage Louisville Riverside Bakersfield Stockton Birmingham Jersey City Norfolk Baton Rouge Hialeah Lincoln Greensboro Plano Rochester Glendale Akron Garland Madison Fort Wayne Fremont Scottsdale Montgomery Shreveport Lubbock Chesapeake Mobile Des Moines Grand Rapids Richmand Yonkers Spokane Augusta Rhichmand Glendale Tacoma Irving Huntington Beach Arlington Modesto Durham Boise Winston Salem); www.clrwtr.com can get SymCom PumpSaver Voltage Monitors to you fast and save you some money!

It will be very helpful if you have the SymCom PumpSaver part numbers ready, then our sales representatives can provide you with a pricing and availability quote for SymCom Load Sensors that you are looking for in seconds. If you do not have the part numbers for SymCom Alternating Relays, our application engineers will be able to help you figure out the part numbers and get the price quote to you as soon as possible.