February 23, 2011
ABB Power Supplies
The CP-T Range of Three-Phase Power Supply Units
is the youngest member of ABB's power supply family. In terms of design and functionality, the new range perfectly supplements
the existing products and extends the range appropriately. The devices can be supplied with a threephase voltage as well as with
two-phase mains. Here, ABB offers power supply units with 24 V DC and 48 V DC outputs with 5 A, 10 A, 20 A and 40 A and
efficiency of up to 92 %.
|
Weidmuller Power Supply
The PRO-M UW
is the perfect power supply solution for all wind power applications: it features the above average power specifications of the
PRO-M series, excellent resistance to shock and vibration, an extremely thin profile, a sturdy snap on metal foot, and 90 %
efficiency. An integrated relay contact monitors the 24 V control voltage and sends an alert in the event of an outage.
|
|
|
|
 |
(800) 894-0412 (888) 723-4773 (Fax)
info@clrwtr.com |
Type IM82-2414 |
The power supplies, type IM82-2414, are designed to power direct current devices, especially switching and
monitoring devices of the TURCK series interface modul, multimodul and multisafe, as well as light barriers and sensors. The
power supply provides an output voltage of 24 VDC and an output current of 1.4 A. The cyclic overload protection is activated
if the current is higher than 1.6 A. The device provides safety extra-low voltage (SELV) according t EN 60950, protection
class II. The device is approved by UL and CSA.
If the front panel LED illuminates green, the connected consumers are provided with power. The "power good"
relay is energized of the output voltage is higher than 21 V. If the voltage drops below this value, the relay is de-energized
and the LED illuminates red. The AC voltage inputs may only be used alternatively and not for prime power distribution.
During operation the removable terminal blocks must be plugged in. When installing the device, please ensure that heat can
dissipate easily.
|
|
If you are looking for TURCK Power Supplies, please call us on
(800) 894 - 0412 or email us at
info@clrwtr.com
we will do our best to help you find the TURCK Voltage Monitors that you are looking for at competitive prices. If you are searching
for TURCK Power Supply technical information (data-sheets) please use the datasheets or product selection guide page
links.
|
MK82 Series |
The MK82 power supplies are a convenient source of power for DC loads: The MK82-2401 provides 24 VDC / 100 mA
to sensors or other multimodul devices.
The output of the device is short-circuit and overload protected. The use of transformers per DIN EN 60742
assures safe galvanic isolation. An illuminated green LED on the front cover indicates that power is being supplied to the
loads.
|
IM82-2450-PS Series |
The power supplies IM82-2450 are designed for DC loads, especially for switching and monitoring devices
of the TURCK seriesinterfacemodul, multimodul and multisafe IME, IMC und IMB. The power supply provides an output voltage
of 24 VDC and an output current of 5 A. The output voltage is adjusted in a range between 23 to 29 VDC with the
potentiometer Vout. The device provides safety extra-low voltage (SELV) according to EN 60950.
If the controlled system is interruped due to faulty power supply, the output voltage U1 increases to
approx. 35V. Thereupon an independent monitoring circuit is activated and the power supply is cut off. Only power cutoff
disables this function. After a delay of approx. 1 min. the monitoring circuit is reset and the power can be switched on
again.
|
MK83-U24 Series |
The voltage monitor MK83-U24 is designed to monitor 24 VDC supply voltages for overvoltage, undervoltage
and ripple. Typical applications are:
- fuse failures in three-phase systems
- voltage monitoring of battery charging systems
- fault indication for power supplies
- overload control
This voltage monitor features two relay outputs (1 NO and 1 NC contact). The switching status is
indicated by a green LED: it illuminates, if the voltage levels are correct; it turns off, if there is an error
condition.
- 1-channel voltage monitor
- Monitoring of 24 VDC power supplies
- 1 NO and 1 NC output contact
- Green LED for switching status indications
|
|
Our industrial factory automation supply distributors warehouse in Boise, Idaho stocks some TURCK products
enabling us to further assist you in finding the correct TURCK power supply for your application in the USA, Canada and
Mexico. Whether we have TURCK voltage monitor in stock in Boise, Idaho or need to ship direct from TURCK to any USA cities;
Clearwater Tech can get TURCK power supply to you fast and save you money! It will be very helpful if you have the TURCK
voltage monitor part numbers ready, then our sales representatives can provide you with a pricing and availability quote for
the TURCK power supplies that you are looking for in seconds. If you do not have the part numbers for BALOGH power supply,
our application engineers will be able to help you figure out the TURCK part numbers and get the price quote to you as soon
as possible.
|
|
|
|
 |
|
| Part Number: |
|
|
Can't find a part number?
E-mail Us! |
|
|
