Analog Signal Conditioners
Relays
Optos
Power Supply

NK Converters

Use Any 4-20 mA Output Sensor as an input to the NK Technologies ADC analog-to-Modbus converter: Current, voltage, temperature, or any parameter that the application calls for. With the digital Modus output scaled for zero (4 mA) to 100 percent (20 mA) the signal will represent whatever you may need to measure. DIN Rail Kits provide a convenient method to facilitate the mounting of the AGL, VTR, APT & APMR series

Red Lion Sensors

Utility Thermocouple Probes are basic products for temperature measurement. They are typically connected to a hand held thermometer. The unit features a rugged handle that is permanently molded to a probe sheath. A retractable cable is connected with strain relief to the handle end, and termination is provided by a miniature male connector. The spring-loaded compression fitting thermocouple is ideally suited

Weidmuller

Loading

Home   >   Products   >   Weidmueller   >   Electronics

Weidmuller

(844) 331-9375       (888) 723-4773 (Fax)
info@clrwtr.com

Weidmuller ACT20X NAMUR Isolating Switching Amplifiers: With Relay Output Distributors

Analogue Signal Processing

When used for industrial monitoring applications, sensors can record ambience conditions. Sensor signals are used within the process to continually track changes to the area being monitored. Both digital and analogue signals can occur. Normally an electrical voltage or current value is produced which corresponds proportionally to the physical variables that are being monitored.

Analogue signal processing is required when automation processes have to constantly maintain or reach defined conditions. This is particularly significant for process automation applications. Standardised electrical signals are typically used for process engineering. Analogue standardised currents / voltage 0(4)-20 mA/ 0-10 V have established themselves as physical measurement and control variables.

Weidmuller meets the ever increasing challenges of automation and offers a product portfolio tailored to the requirements of handling sensor signals in analogue signal processing. The analogue signal processing products can be used universally in combination with other Weidmuller products and in combination among each other. Their electrical and mechanical design is such that they require only minimal wiring efforts.

If you are looking for Weidmuller Electronic Components, please call us on (844) 331-9375 or email us at info@clrwtr.com we will do our best to help you find the Weidmuller Analog Signal Converters that you are looking for at the most competitive prices possible. If you are searching for Weidmuller Optocouplers technical information (data-sheets) please use the datasheets or product selection guide page links.

Weidmuller RIDERSERIES Complete Relay Couplers Distributors
Relay Modules

Relay Modules

Relays are available in different forms - from modular terminal enclosures to plug-in bases for terminal rail mounting.

For switching and amplification of digital signals in automation engineering as well as for electrical isolation between control and load circuit.

The input voltages (coil voltage) lie between 5 and 230 V AC/DC depending on type.

Different types of contacts such as NOC, NCC and CO contacts are available at the output The use of different contact materials enables the switching of power ratings from just a few mW to max. 4 kVA.

Weidmuller PRO-M Series Industrial Power Supplies Distributor

Power Supplies

Power supplies from Weidmuller have long since proved their worth in supplying electrical modules.

They can therefore be used safely in harsh industrial environments, in small businesses and in residential areas, and have been granted international approvals.

Weidmuller can supply power supplies and additional components for industrial applications: Unregulated power packs, Primary switched-mode power units, DC/DC converter, Uninterruptible power system control modules & Electronic fusing.

Class I II Lightning Arresters Distributors
Overvoltage Protection

The priority you give to overvoltage protection depends on your willingness to take risks! Perhaps you think "it will never happen to me". Then you will not have lost anything, but will have gained only very little. However, the subject of overvoltage is then a daily worry for you.

But if you wish to be on the safe side, you should include overvoltage protection in your corporate strategy. Such an investment brings you operational reliability and can prove invaluable when disaster strikes.

Weidmuller FBCon PROFIBUS-PA ATEX Distributor for Ex Areas
FBCon Fieldbus Distributor

The FBCon Fieldbus distributor is available in the industry and EEx (ia) version. They are used for coupling from 1 to 8 field devices or sensors. They are connected via spur lines.

The connection to the spur line can be optionally made with an M12 or 7/8 plug or directly via an EMC cable gland. Communication and device power feed are transferred by a common 2-wire line. The PROFIBUS-PA and Fieldbus Foundation have this same feature.

IEC 603-1 Interface Units Distributors
Interface Units

The interface components are available as a clear alternative to the point-to-point wiring system in order to reduce costs and to simplify the setup of the electrical cabinets. The main function of this interface is as an adapter between the control devices and field elements.

The pre-assembled cables supplied by Weidmuller are also used to connect the tester with the interface.

Rectifier Modules Distributors
Function Modules

The following products are available as functional components:

  • Switch and button components in a sealed built-in EG2 enclosure
  • Rectifier and fuse components in a sealed built-in EG2 enclosure
  • Logic components with AND, NAND, OR and NOR operators
  • Diode gates with up to 40 inputs in open design
  • Components modules for the integration of electronic elements
Weidmuller DIN-Rail Mountable Receptacles AC Outlets Distributors
DIN Rail Receptacles

DIN Rail Receptacles

DIN-rail receptacles, 5A, 15A and 20A power outlets, provide a convenient power source for portable computers or test devices for in-the-panel troubleshooting. They mount on standard 35mm DIN-rail. The terminations accept slotted or Phillips screwdrivers. The mounting foot includes a latching lock - slide it open, mount the module on the DIN-rail and slide the lock closed.

  • Easily snaps onto 35mm DIN-rail
  • Panel mountable, model dependent
  • 5A, 15A or 20A versions
  • Easy to wire
  • Available with ground fault current interrupt (GFCI) or standard outlets
  • Optional power-on indication with GFCI
  • NEMA rated enclosure with UL94 VO flammability rating
  • UL508A, cULus, and cURus and CSA approved
  • Latching mounting foot makes installation and removal from DIN-rail easy

Our industrial factory automation supplies distributors warehouse in Boise, Idaho USA stocks some Weidmuller products enabling us to further assist you in finding the correct analogue signal converter in the USA, Canada and Mexico. Whether we have relays in stock in Boise, Idaho USA or need to ship direct from Weidmuller to any USA cities; Clearwater Tech can get optos to you fast and save you some money! It will be very helpful if you have the Weidmuller power supply part numbers ready, then our sales representatives can provide you with a pricing and availability quote for surge suppressors that you are looking for in seconds. If you do not have the part numbers for Weidmuller fieldbus components, our application engineers will be able to help you figure out the part numbers and get the price quote to you as soon as possible.

Surge Suppressors
Part Number:
Manufacturer:

Search Tips

Can't find a part number?
E-mail Us!

Fieldbus Distributors
Functional Components
Interface Units
Clearwater Tech   © 2011 PRIVACY POLICY TERMS OF USE LEGAL INFO USAGE POLICY