Weidmuller

Home   >   Products   >   Weidmuller   >   Cutting & Clamping   >   I-Series

(800) 894-0412       (208) 368-0415 (Fax)
info@clrwtr.com

Modular Feed-Through Terminals

The feed-through terminals with IDC2 technology are available in two cross-section ranges:

• IDU 1.5N for 0.21 to 1.5 mm² in 5.1 mm pitch
• IDU 2.5N for 0.5 to 2.5mm² in 6.1 mm pitch

Variants with 2, 3 and 4 connections are available. Modular terminals with 4 connections and split current bar are also available. PE terminals with matching profiles round off the range.

If you are looking for Weidmuller I-Series Terminal Blocks, please call us on (800) 894 - 0412 or email us at info@clrwtr.com we will do our best to help you find the Weidmuller I-Series Modular Feed-Thru Terminal Blocks that you are looking for at the most competitive prices possible. If you are searching for Weidmuller IDC Push-In Terminal Blocks technical information (data-sheets) please use the datasheets or product selection guide page links.

Modular PE Conductor Terminals

The PE terminals with IDC2 technology are available in two cross-section ranges:

• IPE 1.5N for 0.21 to 1.5 mm² in 5.1 mm pitch
• IPE 2.5N for 0.5 to 2.5mm² in 6.1 mm pitch

Variants with 2, 3 and 4 connections are available.

2-Tier Modular Terminals

• The IDK two-tier modular terminals can feed two potentials in one terminal. They are available for cross-sections from 0.21 to 1.5 mm².

Modular Isolating Terminals

The disconnect terminals with IDC2 technology are available in two cross-section ranges:

• ITR 1.5N for 0.21 to 1.5 mm² in 5.1 mm pitch
• ITR 1.5N for 0.5 to 2.5mm² in 6.1 mm pitch

Variants with 2 connections are available. Also available for the 1.5 mm² rated cross-section is a variant with 3 connections.

Modular Fuse Terminals

The fuse terminals with IDC2 technology are available in two cross-section ranges:

• ITR 1.5N/SI for 0.21 to 1.5 mm² in 5.1 mm pitch
• ITR 1.5N/SI for 0.5 to 2.5mm² in 6.1 mm pitch Variants with 2 connections are available.

Also available for the 1.5 mm² rated cross-section is a variant with 3 connections. The basis for this is the disconnect terminals of the IDC2 Series in which the SIHA 3 fuse holder is used.

Modular Hybrid Terminals

• Hybrid modular terminals use the time- and cost-saving IDC2 system on the inside (cabinet) and the "well-known" connections (screw or tension clamp) on the outside (field).

Plug-In Modular Terminals

• Take advantage of the incredible advantages of IDC2 technology.
• fast - secure - compact in conjunction with a plug-in modular terminal.
• The basic principle is amazingly simple:
  • One terminal strip for the functional unit, one plug-in connector for the cable loom fabrication.
  • All that remains to be done is to clip the two units together during final assembly - Just Like a Plug-In Connector. Finished

Modular Initiator/Actuator Terminals

• The modular initiator/actuator system with integral cross-connection and advanced IDC technology.
• Each single terminal has two (or three in the case of separate PE function) clamping points for the voltage supply.
• These are fed via a supply terminal and the internal cross-connections.
• Two further clamping points serve as a feed-through terminal for relaying the signal.

Modular Terminals With Electronic Components

• The IDK 1.5N two-tier modular terminals with electronics are available in various forms with diodes and LEDs.
• Different types are available to solve diverse circuit requirements.
• Terminals with four connections are also available as diode models.

Accessories

• Weidmüller offers users of modular terminals of the I-Series a comprehensive range of accessories that render possible appropriate solutions for all - even non-standard - tasks.
• The accessories must comply with the same quality standards as the modular terminals themselves.

Our industrial factory automation supplies distributors warehouse in Boise, Idaho USA stocks some Weidmuller products enabling us to further assist you in finding the correct modular fuse terminals in the USA, Mexico and Canada. Whether we have modular hybrid terminals in stock in Boise, Idaho USA or need to ship direct from Weidmuller to any USA cities; Clearwater Tech can get plug-in modular terminals to you fast and save you some money! It will be very helpful if you have the Weidmuller I-Series IDC Terminal Blocks part numbers ready, then our sales representatives can provide you with a pricing and availability quote for covers that you are looking for in seconds. If you do not have the part numbers for reducing sleeves, our application engineers will be able to help you figure out the part numbers and get the quote to you as soon as possible.