Weidmuller

Home   >   Products   >   Weidmueller   >   Power Supply   >   Modules

(800) 894-0412       (888) 723-4773 (Fax)
info@clrwtr.com

Weidmuller announces the introduction of a new series of economical, general-purpose industrial power supplies - the PRO-M Series. The PRO-M Series modules have been optimized for use in practically all DC power applications, with a wide range of AC/DC inputs and an extended temperature range of -25° C to +70° C. These new modules feature a slim housing design and high power reserves for reliable start-up of loads with high inrush currents, such as motor starting applications. Excellent electrical specifications and high immunity against fluctuations in input voltage or "Brown-outs" make these compact modules the best choice to power sensitive loads in applications such as tooling and molding.

If you are looking for Weidmuller Power Supplies, please call us on (800) 894 - 0412 or email us at info@clrwtr.com we will do our best to help you find the Weidmuller DC To DC Converters that you are looking for at the most competitive prices possible. If you are searching for Weidmuller ConnectPower Power Supply technical information (data-sheets) please use the datasheets or product selection guide page links.

The powerful new line of PRO-H power supplies - with ATEX and Class I Div. 2 approvals - was designed for use in Ex zones and high-performance sector. The power supply units - with their high power reserves, wide temperature range from -25 °C to +70 °C, and high MTBF (mean time between failures) of more than 0.9 million hours - are perfect for the process sector, power applications, and demanding machine construction tasks.

Solutions are available to fit control voltages from 12 V/24 V to 48 V. The product can be wired in parallel in order to increase the power capacity. A two-channel setup with 100 % active load sharing can also be implemented with an optional redundancy module. This serves to increase your operational reliability. The Remote On/Off function allows you to switch the device on and off remotely. The output status can be signalled over a voltage-free relay or transistor output. The devices are equipped with pluggable connection terminals which allow them to be easily tested.

The T-SERIES is a new generation of high performance DIN-rail mounted single-phase modules designed to work reliably even under demanding factory floor conditions. A high power reserve guarantees reliable start-up of loads with high inrush currents.

Excellent electrical specifications and high immunity against fluctuations on input voltage makes these compact modules the best choice to power sensitive loads in industrial process control systems, machine tools or other demanding industrial applications. The T-SERIES offers users easy installation with detachable screw terminal block and snap-on mounting on DIN-rails. All models offer a DC-OK signal and external shut down function. Redundant operation with true power sharing is available as an option.

Weidmuller ConnectPower Single-Phase INSTAPower Switched-Mode Unit in installation housing in performance classes 24 and 48 W. The INSTA modules can be universally deployed because of their wide input range from 85 V AC to 265 V AC. They are available with output voltages from 5 V to 48 V.

Weidmuller ConnectPower 1-Phase ECOLINE Switched-Mode Unit in a compact metal housing for rail mounting. Performance classes 70 to 1000 W. The ECOLINE modules can be universally deployed because of their wide input range from 85 V AC to 265 V AC. A floating relay contact in the output circuit indicates short-circuits and overloads.

Weidmuller ConnectPower 3-Phase ECOLINE Switched-Mode Module unit in compact metal housing for rail mounting. Performance classes 250 to 1000 W. The ECOLINE Modules can be universally deployed because of its wide input range from 340 Vac to 575 Vac. A floating relay contact in the output circuit indicates short-circuits and overloads.

Weidmuller Connect Power Single-Phase Switched-Mode Module unit in a compact metal housing for rail mounting. Performance classes 55 W, 160 W, 300 W. These power supplies can be universally deployed because of their wide input range from 85 V AC to 265 V AC. They are available with output voltages of 5 V, 12 V, 24 V and 48 V. The 300 W ConnectPower power pack includes active PFC control and comprehensive monitoring functions. To increase the power output, up to five power units can be connected in parallel without decoupling on the output side.

Weidmuller ConnectPower Three-Phase Switched-Mode Module Unit in a compact metal housing for rail mounting. Performance class 55 W. The power unit can be universally deployed because of its wide input range from 360 V AC to 480 V AC.

Weidmuller ConnectPower Diode Module for decoupling outputs of switched-mode power supply units. Switched-mode power units have a disadvantage when multiple secondary circuits are switched in parallel, an opposite negative influence can effect the individual circuit. This can damage the devices. The CP DM diode modules can help here. They are used for doubling the output, redundancy operation, supplying critical loads and protecting against energy recovery.

Weidmuller DC / DC Converters for power class 50 W in a compact metal housing for mounting directly on the Terminal Rail. Eight versions are available with rated voltages of 5 V, 12 V, 15 V, 24 V and 48 V on the input and output side.

Weidmuller UPS Control Modules provide the installation with a 12/24 V DC supply within seconds should the power supply fail. Professional signalling guarantees the evaluation of all relevant signal conditions directly in situ: the battery module performs the complete management for external lead batteries. A constant charging and discharging routine guarantees a long service life for the batteries.

Weidmuller ConnectPower Single-Phase WAVESERIES Switched-Mode Modules of the ConnectPower series are suitable for universal because of their variable input from 85 VAC to 265 VAC or 340 to 575V AC. They are offered as single-phase switched-mode units for power classes up to 500 W and as three-phase units for max. 1000 W. The devices have radio interference suppression (to DIN EN 55022 class B) and meet SELV requirements. Primary switched-mode units are fitted with an electronic overvoltage/short-circuit control on the output side. The WAVESERIES units can be used for industial applications as well as and in building automation. National and international approvals are available.

Weidmuller WAVEGUARD is a Selective Electronic Fuse that eliminates negative effects on parallel current paths and cuts out only the defective circuit. A reset input enables the load circuit to be reconnected again. Faults are signalled via a visual indicator and a floating contact. WAVEGUARD fuses are designed for rated currents between 1.6 and 8 A. A version with an adjustable rated current from 0.5 to 5 A rounds off the range.

Weidmuller CompactPower Single-Phase CP NT Power Packs are available in six variants for power classes from 36 to 432 W. The ±15 V tapping on the primary side results in six possible rated voltages: 215 V, 230 V, 245 V, 385 V, 400 V and 415 V. An integral fuse on the secondary side (up to size CP NT192W) protects against overloads and short-circuits. The CP NT 264 W / 432 W is protected via an integrated thermostatic switch.

Weidmuller CompactPower 3-Phase CP NT3 Power Packs are available in six variants for power classes from 250 to 1000 W. The ±5 % tapping on the primary side results in three possible rated voltages: 380 V, 400 V and 415 V. The CP NT3 units are protected against overloads and short-circuits by an integral thermostatic switch.

Electrical-cabinet socket outlet

• Simple installation in electrical cabinet
• TS35 module can be mounted on rail
• VDE mark of conformity
• Two-pole with earthing contact

Our industrial factory automation supplies distributors warehouse in Boise, Idaho USA stocks some Weidmuller Power Supply Products enabling us to further assist you in finding the correct Weidmuller Module in the USA, Canada and Mexico. Whether we have Weidmuller DC/DC Modules in stock in Boise, Idaho USA or need to ship direct from Weidmuller to any USA cities; Clearwater Tech can get Weidmuller ConnectPower Modules to you fast and save you some money! It will be very helpful if you have the Weidmuller Power Supply part numbers ready, then our sales representatives can provide you with a pricing and availability quote for Weidmuller DC/DC Converters that you are looking for in seconds. If you do not have the part numbers for Weidmuller Diode Modules for Redundancy, our application engineers will be able to help you figure out the part numbers and get the price quote to you as soon as possible.